A cube with a side length of 1m is heated uniformly a degree Celsius above the room temperature and all the sides are free to expand. What will be the increase in the volume of the cube? Consider the coefficient of thermal expansion as unity.

A cube with a side length of 1m is heated uniformly a degree Celsius above the room temperature and all the sides are free to expand. What will be the increase in the volume of the cube? Consider the coefficient of thermal expansion as unity.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Related questions

Q: 2/13 In the final stages of a moon landing, the lunar mod- ule descends under retrothrust of its…

Q: The COP of the cycle is

A: Given. T1=100C h=402 kJ/kgT2=500Ch=432 kJ/kgDetermine the COP of the cycle ?

Q: 2/42 Packages enter the 3-m chute at A with a speed of 1.2 m/s and have a 0.3g acceleration from A…

A: Given:Velocity of package at A, VA=1.2 m/sAcceleration of package in chute, aAB=0.3g

Q: Determine maximum shear stress Maximum principal stress=33.227 MPa Minimum principal stress=22.227…

A: Given data : Maximum principal stress=σ1 Minimum principal stress=σ2 Required : Maximum shear…

Q: A piston cylinder device containing 2.5 kg of steam at 700 kPa and 250°C undergoes a constant…

A: m = mass of steam = 2.5 kg P1 = 700 kPa T1 = 250 oC x2 = quality at state 2 = 70% Process 1-2 is…

Q: 200 MPa 100 MPa 300 MPa

A: Given Data: Normal stresses in x and y directions, σx=300 MPa σy=-200 MPa Shear stress, τ=100 MPa…

Q: 2/110 Write the vector expression for the acceleration a of the mass center G of the simple pendulum…

A: Calculate the tangential acceleration. at=rα=22.45=4.90 m/s2

Q: The aerodynamic resistance to motion of a car is nearly proportional to the square of its velocity.…

Q: Refrigerant vapor enters into the compressor of a standard vapor compression cycle at 10°C (h= 402…

A: Given data: At 10°C, h1=402 kJ/kgAt 50°C, h2=432 kJ/kgAt 30°C, h4=237 kJ/kg Need to determine…

Q: The car passes through a dip in the road at A with a constant speed which gives its mass center G an…

A: GIVEN DATA- Acceleration a=0.5g m/s2 Radius of Curvature=100m We have to find Velocity

Q: Two new air-conditioning units are charged for the first time. To be fullycharged, unit A needs 20…

A: Write the given data. Refrigerant for A=20 ouncesRefrigerant for B=14 ounces

Q: 2/110 Write the vector expression for the acceleration the mass center G of the simple pendulum in…

A: Given data as per question θ= 60° θ' = 2.00 rad/s and θ"= 2.45 rad/s2

Q: The slider P can be moved inward by means of the string S as the bar OA rotates about the pivot O.…

Q: Maximum fluctuation of kinetic energy in an engine has been calculated to be 2600 J. Assuming that…

Q: If the stress is 33 MPa and Modulus of elasticity is 58.7 MPa. What is the strain value. Apply hooks…

A: Given data : Stress is denoted by σ Modulus of elasticity is denoted by E Required : Strain

Q: The work done during polytropic expansion of gas from state 1 to state 2 is given by: 1 W = - (P₂V₂…

A: Since you have posted a question with multiple sub-parts, we will solve three subparts for you. To…

Q: The 18-lb box shown is attached to a spring that has a k=2 lb/in and an unstretched length of 14…

Q: diameter of the riser (in cm)

A: Given, Dimension of a cylindrical side riser is= 25 cm×15cm×5cm Tabulated data is given as, Shape…

Q: Q6: Determine the force in members DE, HG, BC, and BG of the truss shown in Fig.(6). and state if…

A: ◆ First, calculate the reaction at the roller support G using equilibrium equations. ◆ To find out…

Q: Learning Goal: To calculate the components, magnitude, and direction of the resultant force of three…

Q: 1.2 /232 Rotation of the arm PO is controlled by the hori- zontal motion of the vertical slotted…

Q: The quadratic prism OABCKLMN. if a=24 m, b=7m, and c=10 m. The prism has width h=14 m. The forces F1…

A: We can answer up to 3 sub-parts so we will answer first 3 for you. Please resubmit the question by…

Q: Consider the situation shown where a 15-kg box is to be held on a steep vertical slope by a cord…

Q: 3/3 The 100-kg crate is carefully placed with zero velocity on the incline. Describe what happens if…

Q: One kilogram of steam at 17 bar and 85% quality expands isothermally to a pressure of 0.7 bar. Find…

Q: The magnitude and direction of Coriolis component of acceleration is

A: Given data, From the figure, Link 2 rotates with constant angular velocity=ω2Slider link 3 moves…

Q: value of the slope at the free end is

A: Given, Flexural rigidity of a cantilever beam is constant.If load P and bending moment PL2 are…

Q: Nutrient media is flowing at a rate of 1.5 L min-¹ in a tube that is 5 mm in diameter. The walls of…

A: Write the given data. Q=1.5 L/min=1.5×10-360 m3/s=2.5×10-5 m3/sd=5 mmA=500×10-6 m2η=0.0012 Pa·s

Q: Find the pressure Force=0.33 N Area 0.2 mm2

Q: Find the pressure at depth of 2.556 m from top of water. Take density of water as 1000 kg/m3

Q: Air is flowing steadily through a horizontal heated tube. The air enters at 40°F and at a velocity…

A: Given: Inlet temperature of the air, T1 = 40o F Velocity of air at inlet of the heated tube, V1 = 50…

Q: What is the range advantage of the defenders over the attackers, i.e. the width of the zone where…

A: In this problem, we have to calculate the range. Consider the horizontal direction motion and write…

Q: Which one of the following statements is true

A: Given data, 4 bar mechanism with all revolute pairs has link lengths, lf=20 mm lin=40mm lco=50mm…

Q: 3/222 The 3-kg sphere moves in the x-y plane and has the indicated velocity at a particular instant.…

Q: The slider P can be moved inward by means of the string S as the bar OA rotates about the pivot 0.…

A: Given θ=0.4+0.12t+0.06t3r=0.8-0.1t-0.05t2 t = 2s To find Velocity Acceleration Angle alpha for…

Q: the average heat transfer coefficient

A: Given. For laminar forced convection over plate,If free stream velocity increases by a factor of…

Q: Ethylene vapor is cooled at 1 atm from 900 to 40°C by heat transfer to the surroundings at 25°C. (a)…

Q: The lead and tin are partially dissolved in each other in solid state although they completely…

Q: b) The shaft shown in figure 6 supports the three pulley loads. The shaft is made of steel and has a…

Q: Find the motion of the system in the figure below with mass 0.25 kg, no damping, spring constant 1…

A: Write the differential equation of motion.…

Q: The 100N force in figure below is the resultant of the couple and three forces, two of which are…

Q: b) Air at 25°C and 1(atm) is cooled at the rate of 3000 m³/hr to -8°C by refrigeration. For a…

Q: A motor supplies a moment M to the pulley of radius R1 (Figure P3.8). A belt connects this pulley to…

A: Solution:

Q: A- Womersley number (a) of a human aorta is 20 and for the rabbit aorta is 17, the blood density is…

A: Solution:

Q: a: Sketch within a cubic unit cell the following crystallographic directions: [121]. (2011. [213].…

Q: One side of a wall is maintained at 400 K and the other at 300 K. The rate of heat transfer through…

A: Given Ts1=400 KTs2=300 KQ.=1000 WTsur=25oC To find Rate of heat transfer within wall

Q: 2/45 A subway train travels between two of its station stops with the acceleration schedule shown.…

Q: A tank 13 ft deep and 5 ft wide is layered with 6 ft of oil (γ = 50.0 lbf/ft3 ), 5 ft of water, and…

A: GIven H=13ftw=5ftz1=6ft with γoil=50 lbf/ft3z2=5ft with γwater =62.43 lbf/ft3z3=846 with γmercury…

Q: The 0.9-kg collar is released from rest at A and slides freely up the inclined rod, striking the…

Q: 3/1 The 50-kg crate is projected along the floor with an initial speed of 7 m/s at x = 0. The…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

The subject is Mechanics of Deformable Bodies

A cube with a side length of 1m is heated uniformly a degree Celsius above the room temperature
and all the sides are free to expand. What will be the increase in the volume of the cube? Consider
the coefficient of thermal expansion as unity.

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that dissipates 100 W. If the probe surface has an emissivity of 0.8, what is its surface temperature in outer space? State your assumptions in the calculations.
2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is
The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per square meter will be transferred in this system if the temperature difference is 10C?
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
A 0.6-cm diameter mild steel rod at 38C is suddenly immersed in a liquid at 93C with hc=110W/m2K. Determine the time required for the rod to warm to 88C.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.