b) The shaft shown in figure 6 supports the three pulley loads. The shaft is made of steel and has a diameter of 30 mm. The bearings at A and B exert only vertical reaction on the shaft. Determine the equation of the elastic curve equation (equation of the deflection along the length of the shaft) and find the deflection at x = 0.5m. Given: E = 200 GPa, I = ²/4 Figure 6 -250 mm -250 mm -250 mm- 150 N 60 N 150 N

b) The shaft shown in figure 6 supports the three pulley loads. The shaft is made of steel and has a diameter of 30 mm. The bearings at A and B exert only vertical reaction on the shaft. Determine the equation of the elastic curve equation (equation of the deflection along the length of the shaft) and find the deflection at x = 0.5m. Given: E = 200 GPa, I = ²/4 Figure 6 -250 mm -250 mm -250 mm- 150 N 60 N 150 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.7.2P: The cantilever beam ACB shown in the figure supports a uniform load of intensity q throughout its...

See similar textbooks

Similar questions

A temporary wood flume serving as a channel for irrigation water is shown in the figure. The vertical boards forming the sides of the flume are sunk in the ground, which provides a fixed support. The top of the flume is held by tic rods that are tightened so that there is no deflection of the boards at that point. Thus, the vertical boards may be modeled as a beam AB, supported and loaded as shown in the last part of the figure. Assuming that the thickness t of the boards is 1,5 in., the depth d of the water is 40 in., and the height h to the tie rods is 50 in., what is the maximum bending stress in the boards? Hint: The numerically largest bending moment occurs at the fixed support.
A brass bar of a length L = 0.4 m is loaded at end B by force P = 10 kN with an eccentricity e = 6mm. The bar has a rectangular cross section with an h/b ratio of 1.5. Find the dimensions of the bar if the deflection at the end is limited to 4 mm. Assume that E = 110 GPa.
The column shown in the figure is fixed at the base and free at the upper end. A compressive load P acts at the top of the column with an eccentricity e from the axis of the column. Beginning with the differential equation of the deflection curve, derive formulas for the maximum deflection S of the column and the maximum bending moment Mmaxin the column.
Plot the load-deflection diagram for a pinned-end column with eccentric axial loads (see figure) if the eccentricity e of the load is 5 mm and the column has a length L = 3.6 m, moment of inertia L = 9,0 × 106 mm4, and modulus of elasticity E = 210 GPa. Note: Plot the axial load as ordinate and the deflection at the midpoint as abscissa.
The cantilever beam AB shown in the figure has an extension BCD attached to its free end. A force P acts at the end of the extension. Find the ratio aiL so that the vertical deflection of point B will be zero. Find the ratio aiL so that the angle of rotation at point B will be zero.
An aluminum box column with a square cross section is fixed at the base and free at the top (sec figure). The outside dimension b of each side is 100 mm and the thickness t of the wall is 8 mm. The resultant of the compressive loads acting on the top of the column is a force P = 50 kN acting at the outer edge of the column at the midpoint of one side. What is the longest permissible length Lmaxof the column if the deflection at the top is not to exceed 30 mm? (Assume E = 73 GPa
A gold-alloy microbeam attached to a silicon wafer behaves like a cantilever beam subjected to a uniform load (see figure). The beam has a length L = 27.5 m and rectangular cross section of a width b = 4.0 m and thickness t = 0.88 m. The total load on the beam is 17.2 N. If the deflection at the end of the beam is 2.46 m is what is the modulus of elasticity Egof the gold alloy? (Use the formulas of Example 9-2.)
A wide-f hinge member (W 10 × 30) is compressed by axial loads that have a resultant P = 20 kips acting at the point shown in the figure. The material is steel with modulus of elasticity E = 29,000 ksi. Assuming pinned-end conditions, determine the maximum permissible length Lmaxif the deflection is not to exceed 1/400th of the length.
A column, pinned at top and bottom, is made up of two C 6 x 13 steel shapes (see figure) that act together. Find the buckling load (kips) if the gap is zero. Find required separation distance d(inches) so that the buckling load is the same in y and z directions. Assume that E = 30,000 ksi and L = 18 ft. Note that distance d is measured between the centroids of the two C shapes.
-7 A beam on simple supports is subjected to a parabolically distributed load of intensity q(x) = 7q0x(L-x)/L2, where q0is the maximum intensity of the load (see figure). A Derive the equation of the deflection curve, and then determine the maximum deflection Use the fourth-order differential equation of the deflection curve (the load equation).
-6 A cantilever beam .4B is subjected to a parabolically valying load of intensity q(x)=q0(L2x2)/L2 where q0is the maximum intensity of the load (see figure). Derive the equation of the deflection curve, and then determine the deflection Band angle of rotation Bat the free end. Use the fourth-order differential equation of the deflection curve (the load equation).
-3 The deflection curve for a simple beam AB (see figure) is given by v=q0x360LEI(7L410L2x2+3x4) Describe the load acting on the beam.