A cylindrical rod having a diameter of 10.0 mm is to be deformed using a tensile load of 20,500 N. It must not experience either plastic deformation or a diameter reduction of more than 4 x 10-³mm. Referring to the materials listed below, which are/is possible candidates? Justify your choice(s). Material Magnesium alloy Brass alloy Steel alloy Modulus of Elasticity (GPa) Yield Strength (MPa) Poisson's Ration 45 200 0.35 101 300 0.34 207 400 0.30

A cylindrical rod having a diameter of 10.0 mm is to be deformed using a tensile load of 20,500 N. It must not experience either plastic deformation or a diameter reduction of more than 4 x 10-³mm. Referring to the materials listed below, which are/is possible candidates? Justify your choice(s). Material Magnesium alloy Brass alloy Steel alloy Modulus of Elasticity (GPa) Yield Strength (MPa) Poisson's Ration 45 200 0.35 101 300 0.34 207 400 0.30

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints. Materials Modulus of Elasticity, (GPa) Yield Strength, (MPa) Tensile Strength, (MPa) Aluminum alloy 70 300 450 Titanium alloy 107 400 550 Steel alloy 207 500 750
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints.
As a material scientist, you have been requested by an engineer to list down a possiblecylindrical rod alloy to be used in your next project. Each cylindrical rod having adimension of 100 mm long and a diameter of 10.0 mm is to be deformed using a tensileload of 27,500 N. It must not experience either plastic deformation or a diameterreduction of more than 7.5 × 10−3 mm. Based on materials listed in Table 2, which arepossible candidates? Justify your choice(s).
Both yield strength and ultimate tensile strength exhibit the ability of a material to withstand a certain level of load. Which parameter do you prefer to use as a design parameter for a proper selection of materials for structural applications? Explain
What is the maximum value of KIc as per LEFM that can be determined from experiments on a 20 mm thick plate? yield strength= 500 MPa, E= 210 GPa, poission ratio=0.3.
Define the term Modulus of Toughness?
Describe the behavior of tested materials (mild steel and aluminium) as it responds to increasing load, in tensile test experiment.
A); How to determine the yield point for materials that do not exhibit a well defined yield point? Name some of such materials. B); Whatis allowable load/stress. Give two different equations that determine the allowable load/stress.
Define the term Elastic Curve?
Determine the yield strength sy and the ultimate strength su of the A36 steel either from Materials Science class book/notes, or by researching over the internet.
What will be the Poisson’s ratio if the material has a modulus of elasticity of 30 X 10^6 psi and a modulus of rigidity of 11.5 x 10^6 psi?
An engineer is making determinations on the best alloy of steel to use in cables for a cable-stayed bridge. The investigator’s tool is a tensile testing instrument which can measure the strength of the alloys by slowly increasing the load on the cable to the point where the cable breaks and breaking point value (amount of weight on the cable when it fails) can be accurately measured. The investigator also is interested in determining the amount of deformation of the cable (how much it stretches under load conditions which is also very important in structural considerations. The tests must be uniform and consistent to give the precision needed to make valid conclusions about the best alloy for the cables. On the line after the item, identify which type of variable it represents from (a) independent variable, (b) dependent variable, (c) control variable. 1) thickness of the cable _____________ 5) length of the cable _____________ 2) testing room temperature…