A cylindrical rod made from an unknown metal is 350mm long and has a diameter of 10mm. The rod is subjected to a tensile load. It experiences only elastic deformation and elongates by less than 1.0mm under an applied load of 19,800N. Could any of the four metals listed in the table below could be the unknown metal? If so which ones and why? Material Modulus of Yield Ultimate Elasticity / GPa Strength / MPа Tensile Strength / MPа Aluminium 70 255 420 alloy Brass 100 345 420 Copper alloy Steel 110 250 290 207 450 550

A cylindrical rod made from an unknown metal is 350mm long and has a diameter of 10mm. The rod is subjected to a tensile load. It experiences only elastic deformation and elongates by less than 1.0mm under an applied load of 19,800N. Could any of the four metals listed in the table below could be the unknown metal? If so which ones and why? Material Modulus of Yield Ultimate Elasticity / GPa Strength / MPа Tensile Strength / MPа Aluminium 70 255 420 alloy Brass 100 345 420 Copper alloy Steel 110 250 290 207 450 550

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) a) How can we test which can withstandthe most stress, a length of spider web thread or a steel wire of the same length? b) Explain, the differences between a ductile and a brittle material. d) Describe some of the connections between Hooke's Law, Young's Modulus and the tensile properties of materials. e) Explain why alloying makes metals harder. f) Describe the differences between an amorphous and a crystalline material.
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 1.3 mm when the applied load is 29,000 N, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).Material Modulus of Elasticity (GPa ) Yield Strength (MPa) Tensile Strength (MPa)Aluminum alloy 70 225 420Brass alloy 100 325 420Copper 110 210 275Steel alloy 207 450 550
Q1a) A sample of an aluminum alloy has a tensile strength of 275 MPa, What will be the maximum force that can be withstood by a rod of that alloy with a cross-sectional area of 2.09 cm2?
HEY MAY YOU PLEASE HELP ME WITH THE FOLLOWING QUESTIONS Which one of the alloys given below will have the highest hardness. Give a brief explanation and illustrate your answer with an applicable calculation. 98% Pb + 2% Mg (RPb = 0.175nm, RMg = 0.160nm) 98% Pb + 2% Sn (RPb = 0.175nm, RSn = 0.151nm)
1. Explain in 1-3 bullets how as a practicing engineer you determine the yield strength of a metal from a tensile stress-strain curve. 2. Explain what is happening at the yield strength for a metal from a physical standpoint in 1-3 bullets. (e.g. what are the atoms doing?)
information: "When performing a tensile test of a metal, these values were found for stress and strain. the yield strength (YS) is stress at 0.2% plastic strain" The task: A 5 meter long rod of this material is loaded axially with a stress of 244 MPa.i. How long is the rod under load?ii. Then the bar is relieved, how long is it now?
Note: Kindly give me both right answers. A) Did the ductile materials (annealed and aluminium) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of ductile materials in compression vs. tension? B) Did the brittle material (quenched) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of brittle materials in compression vs. tension? （Three to five sentence answers are good）（engineering material)
Differentiate between ductile and brittle fracture in materials. Discuss the importance of ductile to brittle transition in BCC and HCP metals.
Determine the value of "Thermal expansion" for a given temperature change of the materials shown in the samples. Lo=20 mm, Copper Alloy C11000 (electrolytic tough pitch), T1=20 C, T2=100 C.dL=?, Lf=?
What is the difference of a non-ferrous alloy and steel components, for example in bicycle? Give at least 5 examples.
- Classify the following materials based on the propertiesbrass trayrubber bandbamboo basketwooden tablesteel chairplastic glasssteel hammerconcrete electric postsoft rockcopper wirespoonmilk canchewing gumknifemalleability-ductility-elasticity-brittleness-hardness-
Discuss (i) fatigue failure of material (ii) S-N Curve with a example of aluminium