A dam 6m on top, 12m at the bottom and 20m high has water 15m depth acting on its vertical side.3. What is the resisting moment?Answer with text and/or attachments:

Answered: A dam 6m on top, 12m at the bottom and…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.11P: A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and...

See similar textbooks

Similar questions

A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
For w = 100lb/ft the resultant concentrated load would be 750 lbs. Where would this force be applied to the cantilevered beam (distance from wall or point A)?
Use moment area method. Note: w, P,, & L values not given final answer in terms of w, P, L
A vertical loads of 400 N acts at the end of a horizontal rectangular cantilever beam 2 m long and 25 mm wide. If the allowable bending stress is 130 MN/m^2, find the depth of the beam in mm
A fiberglass pipe is lifted by a sling, as shown in the figure. The outerdiameter of the pipe is 6,0 in., its thickness is 0.25 in,, and its weightdensity is 0,053 1b/in3 the length of the pipe is L = 36 ft and the distancebetween lifting points is s = 11 ft.a. Determine the maximum bending stress in the pipe due to its ownweight,b. Find the spacing s between lift points which minimizes thebending stress. What is the minimum bebding stress?c. What spacing s leads to maximum bending stress? What is thatstress?
A uniform, 7.5-m-long beam weighing 6490 N is hinged to a wall and supported by a thin cable attached 1.5 m from the free end of the beam. The cable runs between the beam and the wall and makes a 40° angle with the beam. What is the tension in the cable when the beam is at an angle of 30° above the horizontal?
A uniform wooden beam (SG = 0.65) is 10 cm by 10 cmby 3 m and is hinged at A, as in Fig. At what angleθ will the beam fl oat in the 20 ° C water?
When a beam has only uniformly distributed forces applied, the moment diagram consists of piecewise (answer) forces.
A cantilevered beam is loaded with a uniformly distributed load as shown below. If w1 = 2000 lb/ft, what is the value of the moment (ft-lb) at x = 2 ft?(NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)
The vessel is 20m long, 10m wide and 5 m deep. It has a draft of 4, when floating in an upright position. The center of gravity of the scow is on the axis of the symmetry, Find: (a) The initial metacentric height (at initial position) (b) The metacentric height in tilted position when the vessel is at the point of submergence. (c) The distance between weight and the buoyancy in tilted position. (d) The moment created. (e) Classify the kind of moment. (f) The shifted distance of buoyancy.
Draw the Shear Force and Bending Moment Diagram for the loaded simply supported beam shown below. Ignore the self-weight of the beam. Also, Find the maximum bending stress in the beam, if its cross section is rectangular, that it is 15 cm wide and 20 cm deep. Also, determine the stress in a fiber located at 6 cm & 10 cm from the top of the beam.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS

A dam 6m on top, 12m at the bottom and 20m high has water 15m depth acting on its vertical side. 3. What is the resisting moment? Answer with text and/or attachments: