25. A fiberglass pipe is lifted by a sling, as shown in the figure. The outer diameter of the pipe is 100 mm, its thickness is 6 mm, and its mass density is 1500 kg/m³. The length of the pipe is 10 m and the distance between lifting points is 4 m. Determine the maximum bending stress in the pipe due to its own weight.

25. A fiberglass pipe is lifted by a sling, as shown in the figure. The outer diameter of the pipe is 100 mm, its thickness is 6 mm, and its mass density is 1500 kg/m³. The length of the pipe is 10 m and the distance between lifting points is 4 m. Determine the maximum bending stress in the pipe due to its own weight.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.13.4P: A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h =...

See similar textbooks

Similar questions

A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 120 mm and h1= 100 mm. The maximum allowable bending stress in the plastic beam is emix = 6 M Pa, and the bending moment is M = 150 N · m. Determine the minimum permissible width bminof the beam.
A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h = 0,88 in. and h1 = 0.80 in. The maximum allowable bending stress in the metal beam is emax = 60 ksi, and the bending moment is M = 600 lb-in. Determine the minimum permissible width bminof the beam.
A timber dam is made of planking backed by vertical piles. The piles are built-in at the section A where they enter the ground and they are supported by horizontal struts whose center lines are 10 m above A. The piles are spaced 1 m apart between centers and the depth of water against the dam is 10 m. Assuming that the thrust in the strut is two-sevenths the total water pressure resisted by each pile, sketch the form of the bending moment and shearing force diagrams for a pile. Determine the magnitude of the bending moment at A and the position of the section which is free from bending moment. (Cambridge). i. 238 kN-m; 0.75 m from A. ii. 238 kN-m; 0.75 m from B.
A fiberglass pipe is lifted by a sling, as shown in the figure. The outerdiameter of the pipe is 6,0 in., its thickness is 0.25 in,, and its weightdensity is 0,053 1b/in3 the length of the pipe is L = 36 ft and the distancebetween lifting points is s = 11 ft.a. Determine the maximum bending stress in the pipe due to its ownweight,b. Find the spacing s between lift points which minimizes thebending stress. What is the minimum bebding stress?c. What spacing s leads to maximum bending stress? What is thatstress?
Determine the normal force, shear force, and bending moment BY USING THE LEFT SIDE at C ofthe beam in Fig. 7–5a.
1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shear in kN. 3. Determine the location of Neutral Axis, in mm, from the top of the section. 4. Determine the location of the centroid, in mm, from the left of the section. 5. Determine the moment of inertia of the section in x106 mm4 . 6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa. 7. Determine the maximum flexural stress experienced by the beam in MPa. 8. Determine the maximum shearing stress in MPa at Neutral Axis. 9. Determine the spacing of rivets in mm. 10. Determine the maximum flexural stress at 1 m from the support at D to E in MPa.
Derive the formula for the bending stress of a beam with a rectangular cross section and triangular cross secrion. Thank you
A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are b1 = 6.5 in., d1 = 1.5 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.6 in., and d3 = 1.8 in. Determine:(a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative.(c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative.(d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 0.63 in from the bottom of the beam on a section 1.68 feet to the right of B if P = 2290 lb, Q = 8457 lb, w = 1.37 in, L = 8 in, b = 3.7 in, and h = 1.12 in. Round off the final answer to two decimal places.
The steel beam has the cross section shown. The beam length is L = 6.7 m, and the cross-sectional dimensions are d = 390 mm, bf = 205 mm, tf = 14 mm, and tw = 10 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 230 MPa.
A beam having a tee-shaped cross section is subjected to equal 13 kN-m bending moments, as shown. Assume bf = 95 mm, tf = 25 mm, d = 165 mm, tw = 40 mm. The cross-sectional dimensions of the beam are also shown. Determine(a) the centroid location (measured upward from the bottom), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H (positive if tensile and negative if compressive).(c) the maximum bending stress (positive if tensile and negative if compressive) produced in the cross section.
A beam is subjected to equal bending moments of Mz = 57 kip·ft. The cross-sectional dimensions are b1 = 8.3 in., d1 = 1.4 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.4 in., and d3 = 1.7 in. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.