A decoder 74LS138 is to interface with 8086 microprocessor and a memory for perfect communication. Their specifications are 16 pins, 8- active output with 1 active at a time, 6 –input- main (A0 –A3) and enable (E1-E3). With a pin diagram of 74LS138 decoder/ DE multiplexer with much knowledge in microprocessor interfacing design a truth table of a perfect configuration and explain how the truth table is applicable to the specify microprocessor

A decoder 74LS138 is to interface with 8086 microprocessor and a memory for perfect communication. Their specifications are 16 pins, 8- active output with 1 active at a time, 6 –input- main (A0 –A3) and enable (E1-E3). With a pin diagram of 74LS138 decoder/ DE multiplexer with much knowledge in microprocessor interfacing design a truth table of a perfect configuration and explain how the truth table is applicable to the specify microprocessor

Name: A decoder 74LS138 is to interface with 8086 microprocessor and amemory
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: A decoder 74LS138 is to interface with 8086 microprocessor and amemory for perfect communication. Their specifications are 16 pins, 8-active output with 1 active at a time, 6 –input- main (A0 –A3) and enable(E1-E3). With a pin diagram of 74LS138 deco

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Similar questions

Computer Science Suppose, a control register of 8155 PPI has an address of 1Fh. If following instructions areexecuted in an 8085 microprocessor system, then derive the all the port functionalities (i.e.,including pins) of the 8155 PPI.MVI A, ABhOUT 1Fh
The 8051 serial port supports full duplex operation, with transmit and receive buffersthat are available via the SBUF register. Each buffer has an interrupt flag, symbolisedas TI and RI, respectively.i) Briefly state what is meant by full duplex communication. ii) Write a small assembly language program to show how the serial interface can beused for the reception of characters using the serial interface interrupt. Thereceived character(s) should be copied into R0. You must show how theinterrupt is configured; however, you can omit all details of the timer setup. iii) Assuming this code is run on a classic 8051 using a 16 MHz crystal, show howyou would configure Timer 1 for a baud rate 9600 bits/sec and calculate theresulting percentage error. Assume the serial interface is set for 8-bit UART mode,the SCON bit is 0, and the timer is to operate in 8-bit auto-reload mode. You mustshow the values of SCON, TCON, TMOD and TH1.
in 80886 microprocessor Suppose that. DS = 0200H, BX = 0300H, and DI-400H Determine the memory address accessed by each of the following instructions, assuming real mode operation: (1) MOV AL,[1234H] (2) MOV AX,[BX] (3) MOV [DI]AL
Help please mcq In the 8086 computer system using 15MHz crystal oscillator, The time required to writing a word to the memory address 0345BH is------------ and the time of reading the word from the memory address 07FFEH is-------.. 1.6 us 1.6 us 1.6 us 800ns 800ns 800ns 533ns 533ns
A 512KB memory is to be connected to an 8088 processor using only 64KB memory chips. The starting address is 80000H. What will be the inputs to the NAND gate decoder for the 5th memory chip? Group of answer choices a.) A19=1, A18=1, A17=0, A16=0 b.) A19=1, A18=0, A17=0, A16=0 c.) A19=1, A18=1, A17=1, A16=0 d.) A19=1, A18=0, A17=1, A16=1
Suppose the state "Yout, MDRin, ALUadd, Zin" determines the fastest possible clock rate for a particular ISA implemented using this simple multicycle processor implementation. If the circuit delay associated with Yout is 1ns, MDRin is 2ns, ALUadd is 8ns, and Zin is 4ns, what is the length in ns of the shortest clock period that will ensure proper operation?
in 8086 Identify the addressing modes used for the source and destination operands, and thencompute the physical address for the specified operand in each of the following instructions:(Assume all missing data.)1. MOV CX, [DI] (Source operand)2. MOV [BP]+BETA, AX (Destination operand)3. XCHG BX, [FF02] (Source operand)
The 8086 was ___________than/as the 8088 in communication speed with the other computer components. (faster, slower, similar) The Execution Unit of 8086 consists of __________, ___________________, ________________, and________________. (x x x x x x x x)2 i.e. unsigned byte-sized data type can be used to represent decimal numbers in the range 0 through _________. In signed data type, a ___________ in the position of sign bit (MSB) identifies a positive number; while a 1 (one) identifies a __________ number. The data bus (externally) in 8088 is _________ bits & in 8086 is __________bits. ___________, and ____________, are the two different functional units in 8086. The address bus width of 256 KB of memory is ----------------. The first Intel microprocessor was introduced in the year ------------. The address bus having 33 address lines can address memory of ----------------. Word = _______bits, byte =_______ bits, doubleword =_________bits, nibble=________bits. Binary…
design a complete MIPS Processor(Datapath+Control Unit) for the following subset of MIPS instructions:ALU instructions (R-type): add, sub, and, or, xor, slt Immediate instructions (I-type): addi, slti, andi, ori, xori Load and Store (I-type): lw, sw Branch (I-type): beq, bne Jump (J-type): jthe internal circuit of all components used in the datapath(ALU, adder, Extender and ...) should be included in your design. You can use 32-bit adder, decoder , multiplexer, Memory, and Registers as the predefined component in your design
Computer Science Please answer this question in assembly language with .asm extension. The code given in 99Heater.asm file is: ; ===== Heater and Thermostst on Port 03 ==========================; ===== 99Heater.asm ==============================================; ===== Heater and Thermostst on Port 03 ========================== MOV AL,0 ; Code to turn the heater off OUT 03 ; Send code to the heater IN 03 ; Input from Port 03 AND AL,1 ; Mask off left seven bits JZ Cold ; If the result is zero, turn the heater on HALT ; Quit Cold: MOV AL,80 ; Code to turn the heater on OUT 03 ; Send code to the heater END; ================================================================= Fix the program 99Heater.asm so that the temperature will stay at 21 ºC. Please solve the question in assembly language. I will definitely give you THUMBS UP.
When the content of registers: CS=1234h, IP=0006h, SS= ABCDh and SP=AA00h. The bottom of stack=------------- and the Top of stack=-----------. ABCD0h BBCCEh AACD0h AB006h 12346h B66D0h BBCCEh B66D0h
Using appropriate illustrations show how an 8255A could be connected to an 8051microcontroller I/O pins in memory-mapped and port-mapped configurations. Brieflyexplain the significance of the MOVX instruction in relation to these two configurations.