A ditch contains 10 centimeters of water. Rainwater accumulates in the ditch as follows: 10 centimeters of water in the 1st second, 15 centimeters in the 2nd second, 20 centimeters in the 3rd second, and so on. Assuming that the ditch has sufficient capacity for storage, how many centimeters of water will it have after 10 seconds?

A ditch contains 10 centimeters of water. Rainwater accumulates in the ditch as follows: 10 centimeters of water in the 1st second, 15 centimeters in the 2nd second, 20 centimeters in the 3rd second, and so on. Assuming that the ditch has sufficient capacity for storage, how many centimeters of water will it have after 10 seconds?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 37P

See similar textbooks

Similar questions

The flow into a reservoir over a one hour period is shown in the following table. tt (minutes) 0 10 20 30 40 50 60 dVdtdVdt (gallons/minute) 258 332 370 447 436 435 320 Estimate the total volume entering the reservoir in 60 minute using the flow rate at the beginning of each interval. gallonsEstimate the total volume entering the reservoir in 60 minute using the flow rate at the end of each interval. gallons
a) You run an experiment to estimate the water flow rate of the drip irrigation system in the Elon High Tunnel greenhouse. You randomly place 10 small 1-quart paint buckets in the soil along the irrigation system. The table below summarizes the water volume collected in the buckets. The irrigation system was running for 2 hrs. Each bucket has a diameter of 11.2 cm, and volume was measured in milliliters (ml). What is the average drip flow in the irrigation system in inches/hr? (Hint: look up the formula for the area of a circle if you don't already know it).
A certain fluid is flowing in a 0.5 m x 0.3 m channel at the rate of 3 m/sec and has a specific volume of 0.0012 . Determine the mass of water flowing in kg/sec.(Neat and clean step by step solutions)
A system of three pipes 600 m, 800 m, and 1000 m long that are connected in series carries 600 L/sec of water. If the three pipes are 450 mm, 340 mm, and 400 mm in diameter respectively, what is the diameter of a single pipe that can replace the system? Assume f =0.016 for all pipes.
A sedimentation basin in a water treatment plant treats a flow of 4.7 mgd and has the following dimensions: L= 141; W = 23'; Depth of water = 14. Calculate the overflow rate (OR) for the basin (in units of gallons per minute per square foot, gpm/ft?).
Water flows through a pipe 25 mm in diameter at a velocity of 6 m/s. Determine whether the flow will be laminar or turbulent assuming that the dynamic viscosity of water is taken as1.30 × 10−3 kg/ms and its mass density as 1000 kg/m3. If oil of specific gravity 0.9 and dynamic viscosity 9.6 × 10−2 kg/ms is pumped through the same pipe, what type of flow will occur?
From this figure, is the tank filling or emptying?
Q4) A lagoon has an area of 100 m² and the flow into the lagoon is 15 m/hour. 1. What is the volumetric flow rate in m³/second? 2. What is the residence time in this lagoon in minutes?
Determine the flow of water in cubic centimeters. Asap 10 mins
if you are given the following data, which are demonstrated also in Figure below. H = 1 meter h = 12 meter Hydraulic conductivity (K) = 1.5 meter/day Rate of rainfall (R) = 0.002 meter/day Radius of the drain = 0.15 meter Using the graph of Sadik Toksoz for the solution of Kirkham’s equation, the estimated value of spacing between the drains is equal to .................................. place more sped solve
The design of a city water supply system is shown in the figure. Reservoir A need to supply 0.0938 m3/s to lower reservoirs B and C. The roughness coefficient for all pipes is 0.011. Use table below for the properties of the pipes. a) Calculate the flow rate in pipe 2 ( A. 0.0391 m3/s , B. 0.0513 m3/s C. 0.1997 m3/s , D. 0.0194 m3/s) b) Calculate the flow rate in pipe 3 ( A. 0.0547 m3/s , B. 0.0211 m3/s C. 0.0924 m3/s , D. 0.0380 m3/s) c) Calculate the elevation of water surface in reservoir À to supply the required flow rate (A. 140.00 m B. 160.00 m. C . 150.00 m. D. 170.00 m)
A conical tank 4.5m on top and 4,7m tall has a 60mm diameter orifice at its bottom for its outlet. Assume C = 0.63. The tank is filled with 7000 liters of water. What is the depth of the water in the tank in meters? How long will it take to drain the content of the tank in minutes? show solution and diagram