(a) Draw neat illustrative sketches to bring about the difference between a helical coil tension spring and helical coil compression spring. (b) A helical coil spring is made of round steel wire 6-35 mm in diameter. The mean radius of helix is 31-75 mm, number of complete turns, 12; the spring is close-coiled. If C = 84-36 GN/m², find: (i) The pull required to extend the spring by 25.4 mm, and %3D (ii) The stress in the wire.

(a) Draw neat illustrative sketches to bring about the difference between a helical coil tension spring and helical coil compression spring. (b) A helical coil spring is made of round steel wire 6-35 mm in diameter. The mean radius of helix is 31-75 mm, number of complete turns, 12; the spring is close-coiled. If C = 84-36 GN/m², find: (i) The pull required to extend the spring by 25.4 mm, and %3D (ii) The stress in the wire.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

A bumper for a mine car is constructed with a spring of stiffness k = 1120 lb/in. (see figure). If a car weighing 3450 lb is traveling at velocity v = 7 mph when it strikes the spring, what is the maximum shortening of the spring?
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A helical compression spring subjected to compressive load. The maximum shear stress induced in the cross-section of the wire is 24 MPa. For the same compressive load, if both the wire diameter and the mean coil diameter are doubled, calculate the maximum shear stress induced in the cross-section of the wire?
A closely coild spring of 20 cm mean diameter is having 25 coils of 2 cm diameter modulus of rigidity of the material is 10^7 N/cm^2. What is the stiffness of the spring?
A helical spring is made of 10 m diameter steel wire wound on a 100 mm diameter mandrel. If there are 10 active coils what is spring constant Take: C= 100 GPA What force must be applied to the spring to elongate it by 50 mm?
Design a close coiled helical compression spring for a service load rangingfrom 2500 N to 3000 N. The axial deflection of the spring for the load range is 5 mm. Assume aspring index of 4. The permissible shear stress intensity is 450 MPa and modulus of rigidity,G = 84 kN/mm2.
Calculate the number of coils of a helical spring so that the deflection of the spring may not exceed 1.5 in. under a certain load. The mean diameter of the spring is 2.25 in. and the wire diameter is 0.15 in., with the material having allowable shear stress of 50,000 psi and shear modulus of elasticity of 12 x 10^6.
A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection for the load range is 8mm and the spring index is 6.if the permissible shear stress and module of rigidity for the material of the spring are 380MPa and 90pa respectively, including the effect of the wire curvature. Design the spring by, determine (A)wire diameter (B) mean coil diameter (C) number of active turns (D)total number of turns
Hi sir, Please give right answer Derive from fundamentals, the expression for the strain energy stored in a closed coiled helical spring subjected to an axial load.?
A spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm, respectively, with a spring index of 4. The wire diameter is 6 mm and the modulus of rigidity is 84 GPa. Which of the following is the active number of turns of the spring?
A motor drives a shaft at 12 Hz and delivers 20 kW of power as shown in Fig.4. (a) If the shaft has a diameter of 30 mm, what is the maximum shear stress τmax in the shaft? (b) If the maximum allowable shear stress is 40 MPa, what is the minimum permissible diameter dmin of the shaft? A solid circular bar of diameter d = 50 mm is twisted in a testing machine until the applied torque reaches the value T = 500 Nm as shown in Fig.4. At this value of torque, a strain gage oriented at 45 ° to the axis of the bar gives a reading ε =339 ×10-6 . What is the shear modulus G of the material?