Part 2X Carefully review Section 8.13 and note Equation 8.22. Use the value of Qc to find the If you are having difficulty withthis problem, you may wish toother constant in your set of simultaneous equations. Make sure you used aconsistent set of units.review:Solving EquationsSolving Simultaneous EquationsExponents and LogarithmsDetermine the value of K, in h1.K'ih-15.43E24HintAssistance UsedSave for LaterAttempts: 9 of 10 usedSubmit Answer Current Attempt in Progress(a) Estimate the activation energy for creep (i.e., Qc in Equation 8.22) for the S-590 alloy having the steady-state creep behaviorshown in animated Figure 8.33. Use data taken at a stress level of 300 MPa (43,500 psi) and temperatures of 650°C and 730°C.Assume that the stress exponent n is independent of temperature.(b) Estimate ė, at 600°C (873 K) and 300 MPa.Part 1Excellent!What is Qc in J/mol?Qc =480000J/mol

Answered: Image /qna-images/answer/09788737-1fab-4988-b336-c1717b71d47c.jpg

(a) Estimate the activation energy for creep (i.e., Qc in Equation 8.22) for the S-590 alloy having the steady-state creep behavior shown in animated Figure 8.33. Use data taken at a stress level of 300 MPa (43,500 psi) and temperatures of 650°C and 730°C. Assume that the stress exponent n is independent of temperature. (b) Estimate ė, at 600°C (873 K) and 300 MPa.

(a) Estimate the activation energy for creep (i.e., Qc in Equation 8.22) for the S-590 alloy having the steady-state creep behavior shown in animated Figure 8.33. Use data taken at a stress level of 300 MPa (43,500 psi) and temperatures of 650°C and 730°C. Assume that the stress exponent n is independent of temperature. (b) Estimate ė, at 600°C (873 K) and 300 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There are differences in the mechanical behavior of resulting material from (1) tempering martensite at 600 degrees centigrade and (2) tempering martensite 300 degrees centigrade, mention two differences and explain why the differences occur in each
For an 18-8 Mo stainless steel (Figure 1) subjected to creep, you have been asked to a) predict the time to rupture for a component that is subjected to a stress of 100 MPa at 873 K. b) When the temperature is 500 oC (723 K), what is the maximum allowable stress level for a rupture lifetime of 5 years? 20 years?
The lower yield point for a certain plain carbon steel bar is found to be 135 MPa, while a second bar of the same composition yields at 260 MPa. Metallographic analysis shows that the average grain diameter is 50 µm in the first bar and 8 µm in the second bar. Predict the grain diameter needed to cause a lower yield point of 205 MPa.
(a) A 20 cm long bar (10 mm by 10 mm cross-section) of pure aluminium (Young's modulus = 70 GPa) is subjected to tensile loading. If the bar yields at a load of 14,000 N, what is the maximum elongation at the onset of permanent deformation?(b) For the same bar, if the engineering strains are 0.05 and 0.10 at engineering stresses of 200 and 220 MPa respectively, what would be the work hardening exponent of pure aluminium?
. Suppose that a wing component on an aircraft is fabricated from analuminum alloy that has a plane strain fracture toughness of 40 MPa√m. It has been determined that fracture results at a stress of 365MPa when the maximum internal crack length is 2.6 mm. For thissame component and alloy, compute the stress level at whichfracture will occur for a critical internal crack length of 4.0 mm.
The lower yield point for a certain plain carbon steelbar is found to be 135 MPa, while a second bar of the samecomposition yields at 260 MPa. Metallographic analysisshows that the average grain diameter is 50μm in the firstbar and 8μm in the second bar.a. Predict the grain diameter needed to cause a loweryield point of 205 MPa.b. If the steel could be fabricated to form a stablegrain structure of 500 nm grains, what strengthwould be predicted?c. Why might you expect the upper yield point to bemore alike in the first two bars than the lower yieldpoint?
A batch of casted mild steel has a modulus of elasticity of 200 GPa and a yield strength of 250MPa. Calculate for its modulus of resilience. After cold working the steel, the yield strength increases to 310 MPa. Calculate for the percent reduction in the average grain diameter given σo =70 MPa and k = 0.74.
Animated Figure 9.41 is a plot of the logarithm stress versus the Larson-Miller parameter for an S-590 alloy. A component made of this alloy is subjected to a stress of 600 MPa. At what temperature will the rupture lifetime be 200 h?
A mechanical component is fabricated from a metallic alloy. From the experiment, it is obtained that the fracture of this material occured at a stress of 36 ksi when the maximum internal crack length is 0.10 in. The plain strain fracture toughness of this material is 30 ksi sqrt(in) for this same component and alloy, investigate whether fracture will occur at stress level of 55 ksi when the internal crack length is 0.06 in.
State at what homologous temperature creep may start to become an issue for metals and for ceramics. Then estimate the actual temperature for Al, Ti, ZrO2, and SiC. Is the onset of creep behavior with respect to temperature sudden or gradual?
An 80μm diameter glass fiber is confirmed to have no surface cracks longer than 5μm. If the theoretical strength of the fiber is 5GPa, what can you predict the expected minimum breaking strength of the fiber to be? Your answer should be in units of MPa. Hint: The crack tip size will be no smaller than the ionic diameter (twice the radius) of O^2− and the crack length will be no longer than 5μm.
Explain the phases shown in the attached image of a stress strain cureve for 0.15% carbon steel