For an 18-8 Mo stainless steel (Figure 1) subjected to creep, you have been asked to a) predict the time to rupture for a component that is subjected to a stress of 100 MPa at 873 K. b) When the temperature is 500 °C (723 K), what is the maximum allowable stress level for a rupture lifetime of 5 years? 20 years?

For an 18-8 Mo stainless steel (Figure 1) subjected to creep, you have been asked to a) predict the time to rupture for a component that is subjected to a stress of 100 MPa at 873 K. b) When the temperature is 500 °C (723 K), what is the maximum allowable stress level for a rupture lifetime of 5 years? 20 years?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider an S-590 alloy component as shown in following figure that is subjected to a stress of 200 MPa (29,000 psi). At what temperature will the rupture lifetime be 500h?
Calculate is the largest size (mm) internal through crack that a thick plate of aluminum alloy 7075-T651 can support at an applied stress of: (a) three-quarters of the yield strength, and (b) one-half of the yield strength Assume Y = 1. Given: KIC = 24.2 MPa (sq. rt.(m) and σys = 495 MPa
For a certain high-temperature alloy, failure was reported after 4100 hrs at 680°C when subjected to a stress level of 270 MPa. If the same stress were applied at 725°C, how long would the sample be expected to last? State any assumptions you must make to allow you to make this determination.
Animated Figure 9.41 is a plot of the logarithm stress versus the Larson-Miller parameter for an S-590 alloy. A component made of this alloy is subjected to a stress of 600 MPa. At what temperature will the rupture lifetime be 200 h?
What data would have to be collected to determine the stress exponent for creep? What plot axes would give a linear relationship using this data set?
Tensile and fully reversed loading fatigue tests were conducted for a certain steel alloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa, respectively. If a rod of this material supply were subjected to a static stress of 600 MPa and oscillating stresses whose total range was 700 MPa, would you expect the rod to fail by fatigue processes? Hint: You may want to plot a diagram to aid in presenting your answer.
Is the maximum normal stress theory useful to predict the accurate failure of brittle material?
A low-nickel steel in the heat-treated condition had an 'engineering' tensile strength of 708 N/mm2. The reduction in area of cross-section at the fracture was 44%. What was the true tensile strength of the steel?
In the Table below Data for Mar M 247-a Nickel base superalloy is shown. (1) Plot the steady state strain rate and time to rupture to predict a relationship between the two variables. Provide an equation for the relationship that you see. (2) Give an explanation as to why the fracture elongation is going up with stress.
Tensile and fully reversed loading fatigue tests were conducted for a certain steelalloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa,respectively. If a rod of this material supply were subjected to a static stress of 600MPa and fully-reversed oscillating stresses whose total range was 700 MPa. Assuming garber relationship will this rod fail by fatigue failure
A sheet of a 70% Cu-30% Zn alloy is cold-rolled 20% to a thickness of 3.0mm. The sheet is then further coldrolledto 2.0 mm. What is the percentage cold work?
An NDT examination of a steel component reveals the presence of a 5 mm long edge crack. If plane - strain conditions prevail (KIC = 75 MPa.m0.5), what would be the residual service lifetime of the steel part if it were subjected to repeated stresses of 400 MPa? The Paris law equation for the steel has parameters of A=4X10-37 and m = 4