a) Explain the operation procedures and constraints of the different viscometers especially the used one. b) Explain, with examples, the effects of temperature and shear forces on theNewtonian and non-Newtonian fluids. c) Illustrate the results of the viscosity test of the above motor oil then f it the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Takeu at T = 0°C.

a) Explain the operation procedures and constraints of the different viscometers especially the used one. b) Explain, with examples, the effects of temperature and shear forces on theNewtonian and non-Newtonian fluids. c) Illustrate the results of the viscosity test of the above motor oil then f it the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Takeu at T = 0°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The torque M required to turn the cone-plate viscometer inFig. depends on the radius R , rotation rate Ω , fl uidviscosity μ , and cone angle θ . Rewrite this relation indimensionless form. How does the relation simplify it if itis known that M is proportional to θ ?
A concentric cylinder viscometer may be formed by rotating the inner member of a pair of closely fitting cylinders. The annular gap is small so that a linear velocity profile will exist in the liquid sample. Consider a viscometer with an inner cylinder diameter of 4 in, a height of 8 in, and a clearance gap width of 0.001 in, filled with castor oil at 90 oF. Determine the torque (in lbf×ft) require to turn the inner cylinder at 400 rpm. The dynamic viscosity of the caster oil is 0.0079 lbf×s /ft2.
what is the relationship between the fluid viscosity and the drag force Fdrag?
What is the difference between dynamin and kinematic viscosity? That is the significance of these properties of liquid?
PROB E. A capillary –tube viscometer is being selected to measure viscosity of a liquid food. The maximum viscosity to be measured will be 230 cP and the maximum mass rate is 900 grams per hour. If the tube length is 10 cm and the maximum sustainable pressure is 25 Pa, determine the nominal diameter size of the tube to be used.
It is desired to determine the surface tension of a particular fluid using a capillary-riseexperiment. Kienth used a 0.5 mm glass tube and found that the height of the liquidmeasured 30 mm with a contact angle of 30°. Kienth then performed viscosity measurements using an Ostwald viscometer. He found that the fluid takes 1.5 times slowerto flow through the viscometer relative to water with a density of 1000 kg/m? and aviscosity of 1.0 cP. It is previously known that the viscosity of the fluid is 1.35 cP. Whatis the surface tension of the liquid?
The belt in the Ögure moves at steady velocity V and skims the top of a tank of oil having viscosity. (a) Develop and expression for the required belt drive power in terms of h, L, b, V , and . Recalthat, for steady motion, power is equal to force velocity.(b) What power is required if the belt moves at 5 m/s over SAE 50W oil ( = 0:86 kg/ms) withh = 2 cm, L = 2 m, and b = 0:5 m
A pitot-static probe will be used to measure the velocitydistribution in a water tunnel at 20°C. The two pressurelines from the probe will be connected to a U-tube manometerthat uses a liquid of specifi c gravity 1.7. The maximumvelocity expected in the water tunnel is 2.3 m/s. Your job isto select an appropriate U-tube from a manufacturer thatsupplies manometers of heights 8, 12, 16, 24, and 36 in.The cost increases signifi cantly with manometer height.Which of these should you purchase?
Describe the general principles of dynamic fluid?
An oil film of thickness 1.5 mm is used for lubrication between asquare plate of size 0.9 m × 0.9 m and an inclined plane having anangle of inclination 200. The weight of the square plate is 392.4 N andit slides down the plane with a uniform velocity of 0.2 m/s. Find thedynamic viscosity of the oil
Explain the differences between Newtonian and Non-Newtonian fluid.
A rotating viscometer consists of two concentric cylinders—a stationary inner cyliner of radius Ri and an outer cylinder of inside radius Ro rotating at angular velocity (rotation rate) ?o. In the tiny gap between the two cylinders is the fluid whose viscosity (? ) is to be measured. The length of the cylinders in Fig is L. L is large such that end effects are negligible (we can treat this as a two-dimensional problem). Torque (T) is required to rotate the inner cylinder at constant speed. Showing all your work and algebra, generate an approximate expression of T as a function of the other variables.