answer quickly A flat plate is being injection molded using PLA (a = 0.075 mm2/s) at a temperatureof 110°C. The temperature of the mold wall is set to 40°C and the plate will beejected once it cools to 80°C. If production requirements only allow for a coolingtime of 15 seconds per part, what is the maximum thickness that the plate can be?O 3.7 mm5.9 mm11.1 mm7.6 mm34.9 mm

Given, Temperature conductivity rate, a=0.075mm2/scooling time,t=15secθ=80°Cθs=40°Cθo=110°CTo…

Answered: A flat plate is being injection molded…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pudding mix is being formulated to achieve a total solids content of 20% in the final product. The initial product has a temperature of 60°C and is preheated at 90°C by direct steam injection using saturated steam at 105°C. If there is no additional gain or loss of moisture from the product, what is the total solid content of the initial product?
A pudding mix is being formulated to achieve a total solids content of 20% in the final product. The initial product has a temperature of 60°C and is preheated at 90°C by direct steam injection using saturated steam at 105°C. If there is no additional gain or loss of moisture from the product, what is the total solids content of the initial product?
GKN Sinter Metals Company pressed iron powders using a compaction pressure of 600 MPa to produced a cylindrical bearing which is 70 cm long and has internal and external diameters of 8 cm and 16 cm, respectively. Determine (a) the most appropriate pressing direction, (b) the required press tonnage to perform this operation, and (c) the final weight of the part if the porosity is 12%, given that the density of iron, ρ = 7.87 g/cm3. Assume shrinkage during sintering can be neglected
When designing patterns for casting, patternmakers use special rulers that automatically incorporate solid shrinkage allowances into their designs. For example, a 12-in. patternmaker’s ruler is longer than 1 foot. How long should a patternmaker’s ruler be for making patterns for (a) aluminum castings and (b) high-manganese steel?
A aluminium alloy casting has a cylindrical geometry with 100mm in diameter and weighs 3200 gram. This casting takes 7.5 min to completely solidify. Another smaller and lighter cylindrical-shaped casting with the same diameterto-length ratio weighs 1800 gram. This casting is made of the same aluminium alloy and the same conditions of mold and pouring were used. Determinea) The mold constant in Chvorinov’s Rule,b) The dimensions of the lighter castingc) The total soldification time of the lighter casting. The density of aluminium alloy= 2.7 gram/cm3and n=2
What means product quality ? What characristics does the term product quality include ? 2 - what steps are included in the molding process, list them ?
In 2018, 25% of produced flat glass were recycled back as a raw material in the production of flat glass as it yielded sustainable impacts such as the reduction of energy requirement to heat up the furnace since the mixture will melt easily. In your opinion, can other types of glass wastes (eg. tempered glass, glass bottles, etc) be used as a raw material in the production of flat glass. Justify your answer by providing references.
What happens in the powder mixture if granulation is over wetted and under wetted? How can this be prevented?
Design a closed cylindrical riser with ratio H / D = 2, to obtain the aluminum part shown in the figure, using sand mold casting. The riser must be efficientand prevent bumps / cavities in the part. Assume the mold constant Cm = 6.15 min / cm2
11)Q2. Identify the casting process in which the molten metal is injected in mold/die at high pressure and explain its working principle along with a neat diagram.
a.State and describe the termi. co-extrusion b. Differentiate between single and twin-screw extruders by describing three distinguishing features in each. c. Dealinate three advantages in the application of extrusion cooking.
Explain the extrusion blow molding in detail.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS