Q=2000J Vout =? m (kg/s) 111111 D=0.1m air Air at (5.00x10^2) K flows out of a dcular pipe at 101325 Pa as shown in Figure. The mass flowrate of the air at the pipe entrance is 0.0093 kg/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet Velocity if 2000 J of heat is added to the pipe. Answer should be in m/s with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer 9°C

Q=2000J Vout =? m (kg/s) 111111 D=0.1m air Air at (5.00x10^2) K flows out of a dcular pipe at 101325 Pa as shown in Figure. The mass flowrate of the air at the pipe entrance is 0.0093 kg/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet Velocity if 2000 J of heat is added to the pipe. Answer should be in m/s with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer 9°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the pressure is 765mmHg, and the velocity is 100 m/s. Assuming the flue gas behaves ideally, and the process is isothermal, with the temperature maintained at 100C. Determine the theo. power required to move 45000 m /h of the flue gas.
Nitrogen at a pressure of 200 kPa and a temperature of 25°C, flow at a velocity of 20 m/s through a pipe with a diameter of 35 mm Working substance:______system:______ Sketch :
Argon gas enters a constant cross-sectional area duct at Ma1 = 0.2, P1 = 320 kPa, and T1 = 400 K at a rate of 0.85 kg/s. Disregarding frictional losses, determine the highest rate of heat transfer to the argon without reducing the mass flow rate.
A gas flows steadily through a rotary compressor at a temperature of 16 ⁰C, a pressure of 100kPa, and an enthalpy of 392.2 kJkg-1. The gas leaves the compressor at a temperature of 245⁰C, a pressure of 0.6 MPa and an enthalpy of 534.5 kJkg-1. There is no heat transfer to or fromthe gas as it flows through the compressor. Using the steady flow equation appropriate toeach case, evaluate the external work done per unit mass of gas: a) when the inlet and exit velocities of the gas are negligible b) when the inlet velocity of the gas is 80 ms-1 and the exit velocity of the gas is 160 ms-1.
A vapor enters a group of convergent-divergent nozzles at 3MPa and 300 oC and expands to 0.5 MPa. If the exit velocity and the steamcirculation rate are 800 m/s and 14 kg/s respectively, determine:a- The nozzle efficiency.b- The total cross-sectional area of the nozzles.c-The velocity at the throat
. Steam at an initial enthalpy of 100 kJ/kg and inlet velocity of 100 m/s, enters an insulated horizontal nozzle. It leaves the nozzle at 200 m/s. Determine the exist enthalpy (in kJ/kg).
Nitrogen enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the amount of 150 kJ/kg as it flows through it. The nitrogen leaves the heat exchanger at 100 kPa with a velocity of 200 m/s. Determine the stagnation pressure and temperature of the nitrogen at the inlet and exit states.
Certain oil with sp.gr 0.96 is pumped through a large pipe of diameter 500mm. Velocity of the oil at inlet is 0.2m/s. The outlet of the pipe is at an elevation of 50m above the inlet. The pressure of the oil at the inlet is 50N/cm2. For these conditions determine the volume flow rate and the mass flow rate of oil through the pipe. Determine the total head at the inlet of the pipe and at the outlet of the pipe.
Air at 29oC with a rate of 0.03 kg/s enters a circularpipethat is constructedunderthewater. Thewatertemperature is kept at 17oC andconvectioncoefficientforwater is hw= 1500 W/m2.K Pipeproperties k=0.15 W/m.K Do=17cm Di=15cm a) Inordertoreach an airoutlettemperature of 21oC determinethereguiredpipelength b) What is required fan powertomovetheairthroughthepipe?
Air at 7 kPa, 420 °C, and 400 m/s enters an adiabatic nozzle. The velocity of the air outlet is 700 m/s. Calculate the air outlet temperature.
Liquid benzene at 38 C with a vapor pressure of 26.4 kN/m2 and a density of 860 kg/m3 isto be pumped at a rate of 0.0025 m3/s from a storage tank to a discharge location 3 m abovethe liquid level in the tank. The pump with a mechanical efficiency of 60 percent is 1 mabove the liquid level. The storage tank is at atmospheric pressure. The pressure at the endof the discharge line is 445 kPa absolute. The inside diameter of the pipe used to transfer thebenzene is 0.0409 m. The frictional pressure drops in the suction line and the discharge linehas been evaluated as 3.45 and 37.9 kN/m2, respectively. Determine the head developed bythe pump and the total power requirement. If the pump manufacturer specifies a required netpositive head of 3.0 m, will such a pump be applicable for this service?
Specify the pipe required to carry 272.200 kg of steam per hr at 87.9 kg/cm^2 ga, 538 °C, with velocity approximately 3050 m/min