Problem 04.077. Determine the deflection of an angled bar using Castigliano's theorem Using Castigliano's theorem, determine the deflection of point Bin the direction of the force F= 10 ibf for the steel bar shown in the figure where a= 19 in, b=6 in, and the diameter is d=0.5 in. in The deflection of point Bin the direction of force is

Problem 04.077. Determine the deflection of an angled bar using Castigliano's theorem Using Castigliano's theorem, determine the deflection of point Bin the direction of the force F= 10 ibf for the steel bar shown in the figure where a= 19 in, b=6 in, and the diameter is d=0.5 in. in The deflection of point Bin the direction of force is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An axial member consisting of two polymer bars is supported at C. Bar (1) has a cross sectional area of 2720 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 21,560 mm and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C.
Determine the maximum deflection of a simply supported beam carrying a hydraulic cylinder in a machine used to press bushings into a casting as shown in the figure. The force exerted during the pressing operation in 45 kN. The beam is rectangular, 35 mm thick and 150 mm high, and made of steel (E = 207 Gpa).
Two elastic beams with equal bending rigidity of EI are connected by a pin at B. The beam is fixed at A and a roller support is attached at C. Beam BC is subjected to a uniformly distributed load of magnitude w=1 N/m. If the bending rigidity EI is 108Nmm2, determine a) the lateral deflection at B, b) the rotational angle at B, c) the rotational angle at C. d) sketch the deformed shape
In the figure shown, the deflection of mercury is initially 250mm. If the pressure at a is increased by 40kPa, while maintaining the pressure at b constant, what will be the new mercury deflection?
Question 2: Determine the deflection of D (in inches) with respect to A of the rod shown. Note: Section AC is steel and has a E = 29 x 10^6 psi. Section CD is brass and has E = 14.6 x 10^6 psi.
The part shown is formed from a 1/8 - in diameter steel wire, with R = 2.5 in and l = 2 in. A force is applied withP = 1 lbf. Use Castigliano's method to estimate the horizontal deflection at point A. Justify any components ofstrain energy that you choose to neglect.
Determine the deflection at Point C of the beam shown below (negative is down). P = 16 kN wo = 29 kN/m E = 192 GPa I = 94.145x10-6 m4 Express your answer using three significant figures and ensure that it is in mm.
vi) Using Macauley’s method, determine the deflection of the member at the locations where the 25 kN, 20 kN and 50 kN point loads are applied. Comment on how the maximum deflection of the member could be determined. Material properties for steel: Maximum allowable tensile stress = 750 MN/m2 Maximum allowable torsional shear stress = 375 MN/m2 Young’s Modulus of elasticity = 205 GN/m2Modulus of rigidity = 81 GN/m2Poisson’s ratio = 0
A simply-supported beam, 9 m in length, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. Determine the maximum deflection. Answer: _____/EI
A force tangent to 1.75 feet diameter pulley is 5200 N and is mounted on a 2 inches shaft. Determine the torsional deflection per meter of length if G = 83 x 106 Kpa.
A simply-supported beam, 9 m in length, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. Determine the deflection at x = 7.5. Answer: _____/EI
For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the magnitude of the maximum displacement (in mm) if d = 1.51 m, E = 11.77 GPa , and I =1679930mm4. NOTE: PLEASE ANSWER IT CORRECTLY. IF YOU ARE NOT SURE ABOUT THE ANSWER, PLEASE SKIP THE QUESTIONPLEASE BOX THE FINAL ANSWER(S)THANK YOU! image below for reference