b) Figure 1 shows a center-tap rectifier circuit employing silicone diodes combined with a load network circuit consists of Zener diode, resistors R, = 1kn, R = 1k2 and R, = 5kn. The waveform of the input voltage V,(t) =-V, sin is depicted in Figure 2. Suppose V, = 20V and winding ratio of the transformer is given by a:b =1:2, (1) Sketch the output waveform of V,(1). (i1) Sketch the output wave of V,(t). (ii1) Determine the average de voltage of V,(t). Si a : b V. R IZM = 5mA Io V:(t) RL Ro Vo V =9 V Ši Figure 1

b) Figure 1 shows a center-tap rectifier circuit employing silicone diodes combined with a load network circuit consists of Zener diode, resistors R, = 1kn, R = 1k2 and R, = 5kn. The waveform of the input voltage V,(t) =-V, sin is depicted in Figure 2. Suppose V, = 20V and winding ratio of the transformer is given by a:b =1:2, (1) Sketch the output waveform of V,(1). (i1) Sketch the output wave of V,(t). (ii1) Determine the average de voltage of V,(t). Si a : b V. R IZM = 5mA Io V:(t) RL Ro Vo V =9 V Ši Figure 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
i) Draw the circuit diagram of the single phase full wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation. (ii) A single phase fully controlled bridge rectifier circuit has DC output voltage 175 V for an AC supply voltage of 210 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode
1- A testing transformer 220 V/100 kV (rms), 50 Hz is supplying a half wave rectifier circuit. If the load resistance is 5 MΩ, find: a- The value of the smoothing capacitor so that the time constant is 10 times the supply periodical time. b- The rated peak inverse voltage (PIV) of the rectifier. c- The number of series connected rectifiers if the rated PIV of a rectifier is 20 kV. d- The ripple and the output voltages. the sub-parts to be solved.
(i) A fully-controlled single-phase bridge rectifier is supplied from a 50Hz, 220/120 V transformer .The rectifier supplying a highly inductive load of 10 Ohm resistor. For a firing angle of 45º, determine the rectified voltage, the rectified current and the power factor. (ii) If the current extinction angle β =200˚; Determine whether the current is continuous or discontinuous (iii) Sketch the appropriate load voltage and load current waveform
A fully controlled three-phase rectifier bridge circuit supplies a dc load of 300V,60A, from 415V 3-phase ac supply via delta-star transformer. (i) Determine the required thyristor and transformer specifications. (ii) Draw the load and thyristor voltages when firing angle alpha = 60°. (ii) If a commutating diode is placed across the load, determine the FWD specification and then calculate the average load voltage and FWD average current when firing angle alpha = 45°
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
A bridge rectifier uses a step-down transformer and ideal diodes. If the rectifier delivers an average output voltage of 41.4 V to a 480 ohm load find (i) transformer turns ratio, (ii) the average power delivered to the load.
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed to be (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
Consider the adjacent circuit diagram of three different rectifier topologies connected to an 346 Volt three-phase AC system. Assume a load resistance of 36Ω in ALL instances with NO losses in the rest of the circuit. Observe the connections to the AC supply and determine the parameters for, Rectifier A: 1) the maximum voltage across the load and the dc load voltage; 2) the r.m.s. load voltage and the rectification efficiency; 3 the r.m.s. current rating of the diodes and the conduction period of a single diode; 4 the PIV rating of the diodes
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
Design rectifier circuits to provide an output of 100 VDC using:a) Half wave rectifierb) Center-tapped Full wave rectifier For each circuit, calculate the diode PIV ratings and the transformer turns ratio (secondary to primary), if power is taken from the 220 V line AC supply.