A force F of 10 N is applied in the direction indicated, per meter depth (into page). The 300 mm long triangular beam is Aluminum, 1100 series, and extends 2 meters into the page. What is the moment about point A, per meter of depth? The system is on Earth, at sea level, gravity acts in the direction of F. 40 Note: The centroid of a triangle is located at h/3. 300 A) 16 Nm / m B) 19 Nm / m C) 24 Nm / m D) 27 Nm / m

A force F of 10 N is applied in the direction indicated, per meter depth (into page). The 300 mm long triangular beam is Aluminum, 1100 series, and extends 2 meters into the page. What is the moment about point A, per meter of depth? The system is on Earth, at sea level, gravity acts in the direction of F. 40 Note: The centroid of a triangle is located at h/3. 300 A) 16 Nm / m B) 19 Nm / m C) 24 Nm / m D) 27 Nm / m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.38P: The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the...

See similar textbooks

Similar questions

b)A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is 11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous c) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Suppose that a= 640 mm
Q1. A line RS of 55 mm in length is inclined to HP by 30o and parallel to VP. One of its end points is above HP by 20 mm and in front of VP by 30 mm. The line is in single quadrant. Find the projections of the line RS and find out its horizontal trace.
Generalize Prob. as follows. Denote length AB asH , length BC as L , and angle ABC as θ . Let the dam materialhave specifi c gravity SG. The width of the dam is b .Assume no seepage of water under the dam. Find an analyticrelation between SG and the critical angle θ c for whichthe dam will just tip over to the right. Use your relation tocompute θ c for the special case SG = 2.4 (concrete).
12 - A homogeneous, planar plate of constant thickness in the figure the coordinates of the centroid M(Xm,Ym) of the surface area, Find the team (x,y). t= 3 cm and a= 9 cm. What is the area, in cm2, of the rectangle removed from this planar plate?a) 216B) 120C) 90D) 108E) 180
n this question, you will calculate the second moment of area for a 4 ✕ 6 piece of lumber about the x − x and y − y axes, as shown. A rectangle with height h and width w > h is centered on the origin of the x y-coordinate plane. The left and right sides of the rectangle, having height h, are parallel to the vertical y – y axis and the top and bottom sides, having width w, are parallel to the horizontal x – x axis. Visit a hardware store and measure the actual dimensions of a typical 4 ✕ 6 piece of lumber. (Enter your answers in inches.) h = in w = in Calculate the second moment of area about the x − x and y − y axes using the measured dimensions. (Enter your answers in in.4.) Ix – x = ______in4 Iy – y = ________in4
Find the resultant and angle of direction based on the horizontal. using tail to tip method 1. 43 lb 62 oE of N 2. 11 lb 40 0N of W
a. find the area and vertical distances from the bottom edge of the cross-section to the centoid of rectangles b. Find Iz, the area moment of inertia about the z centroidal axis for the cross-section. c. Find QH, the first moment of area about the z centroidal axis for the entire area below point H. This area has width 2c2c and height tt. Also, find QK, the first moment of area about the z centroidal axis for the entire area above point K with width b and height t. d. Determine the magnitudes of the shear stress at point H and the shear stress at point K. e. Find Qmax, the maximum first moment of area about the z centroidal axis for any point in the cross section, and τmax, the maximum horizontal shear stress magnitude in the cross section.
A block of stone is cut so that its cross‑section is a parallelogram. The width of the bottom side is ?=0.655 m, the height of the top of the block is ℎ=0.915 m, and the top right corner overhangs a distance ?oh=0.195 m from the bottom corner as shown. Assume that the block is of uniform density, so that the center of gravity of the block is located at the geometric center.
Describe the Parallel-Axis Theorem for an Area?
Give me right solution according to the question... F=183 N
A vessel is in the form of an inverted regular square pyramid of altitude 9.87 in. and base edge 6.27 in. The depth of the water it contains is 6 in. a. How much will the surface rise when 1 pt. of water is added? ( 1 gal.=231 cu.in.) b. Find the wetted surface when the depth of water is 9.23 in.?