A frequency response for the open loop system of a crane system is shown in Figure Q2. a) Analyse the transient response, stability and steady state error of the system, then complete Table Q2. Table Q2 Performance Criteria Value Transient Response Phase margin, ØM Gain margin, GM = Bandwidth, wgw Stability The gain crossover frequency, woM = The phase crossover frequency, wgM Stability* : Stable/Unstable/Marginally Stable Static error constant* : Kp/K„/Kq = Steady state Steady state error, e„(∞0) = one answer only

A frequency response for the open loop system of a crane system is shown in Figure Q2. a) Analyse the transient response, stability and steady state error of the system, then complete Table Q2. Table Q2 Performance Criteria Value Transient Response Phase margin, ØM Gain margin, GM = Bandwidth, wgw Stability The gain crossover frequency, woM = The phase crossover frequency, wgM Stability* : Stable/Unstable/Marginally Stable Static error constant* : Kp/K„/Kq = Steady state Steady state error, e„(∞0) = one answer only

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

Q2. Explain how you would determine the primary and secondary constants of transmission by impedance measurements. Also, explain how the velocity of propagation and attenuation constant can be experimentally determined.
Is it possible to measure the phase-shift angle in an AC single-phase circuit by an indirect method using an ammeter and a voltmeter? - Yes, but an instrument must be added to measure the active resistance of the load. - Yes, but an instrument must be added to measure the active power dissipated by the load. - Yes, but an instrument must be added to measure the frequency.
What is the use of phase cross over frequency? How will you find it?
Find the loop current in the circuit shown, using circuit analysis and the gauss seidel method. Accurate with up to 5 decimal places.
To qualify system stability, we use: a. Routh criterion b. Phase margin c. Gain and phase margin d. Gain margin
By plotting the locus-root curve of the open-loop transfer function G(s)= K / s (s+2); a) When K=4, show the locations of the closed loop poles on the root locus. Determine the damping ratio ζ and the natural frequency (wn) values at this gain value. b) Calculate and scale the unit step response of this closed-loop system by calculating the %overshoot, tp and ts (percent overshoot, peak and settling times, respectively). c) In order for this supervised system to work at least in the performance criteria (computed (greater than ζ and wn)) in question (a), scan the region where the pairs of conjugate poles should be located on the root-locus curve.
a) Sketch the root locusb) Using Routh-Hurwitz, determine the maximum gain Kp before system goesunstable
Q2 (A) A frequency modulator is supplied with a carrier at frequency fc = 5 MHz and an audio tone signal of Am = 1 volt amplitude and frequency fm = 1 kHz. It produces a frequency deviation f of 10 kHz as the output of the frequency modulator. (3)(i) The FM waveform described above is passed through a frequency multiplier with a total multiplication factor of 18, that is, fout = 18*fc. After passing through the frequency multiplier, what is the frequency deviation f at the output?(ii) The output of the multiplier in part (a) is next input to a mixer stage with the LO oscillator frequency set at fLO = 55 MHz. Find the sum-frequency output fo of the mixer’s IF port and also find the magnitude of the frequency deviation f.
Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
Each item below describes key characteristics of a particular system (that is, a plant transfer function). For each system, describe the effect of proportional control on the stability of the closed-loop system. Specifically, 1) what can you say for small gains, and 2) what for large gains? (E.g., stable, unstable, inconclusive.) Provide a short explanation of your answers, with sketches as necessary.
Determine the z parameters for the circuit in following Figure?
Using the given transfer functions of the open-loop system, investigate the stability of the closed-loop system using the Nyquist criterion: