Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V. Consider the half-wave rectifier circuit shown in the figure boclow. Let Ug be a sinusoid with10V peak amplitude with frequency of 60 Hz, and let R = 1 k2. Use the constant-voltage-drop diode model with Vp = 0.7 V.え。%3DD.Rkuf27f =VSEFigure 1: Question2 Rectifier Circuit (a) Sketch the transfer characteristic function of vo vs US-(b) Sketch the waveform of uo on the same graph with vs over at least two (2)cycles of us(c) Find the peak current through the resistor R(d) Sketch the output waveform vo if a capacitor C is connected in parallel withR.(e) Calculate the value of the capacitor C that will ensure that the voltagepeak voltage and lowest voltage is no greater that 10% of the peak voltage

Answered: Image /qna-images/answer/11689378-089d-453e-a529-b0741015ccd4.jpg

Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.

Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Related questions

Q: A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of2KΩ i. Draw…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Consider a peak rectifier fed by a 60-Hz sinusoid having a peak value Vp = 100 V. Let load…

A: Given:Frequency,f=60HzVP=100VR=10KΩVR p-p=2V

Q: Determine the peak output voltage for the bridge rectifier. Assuming ideal model, what PIV rating is…

A: The solution is given below

Q: a. Draw a circuit diagram for a full wave rectifier with a capacitor filter. What does the charging…

A: Full wave Rectifier, Circuit diagram of the full wave rectifier with capacitor filter. How to…

Q: 4. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 (a) If…

A: In this question we will find full bridge rectifier related problems....

Q: In the single-phase diode rectifier circuit shown in Figure 1 and a constant dc load current la=…

A: The given details are :-Vs=120 V RHS supply voltagef= 60 HZId= 10 A Average output currenti) The…

Q: a) Write down the characteristic equation of a semiconductor diode. b) What happens in a…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a.…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply…

A: There are many devices that work with DC supply, but the supply present is naturally AC. The…

Q: Using neat circuit diagram and waveforms, illustrate the operational modes of a Single-Phase…

A: Single phase controlled bridge rectifier We have considered here a single phase full controlled…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a.…

A: As per the guidelines of Bartley we supposed to answer first three subpart only

Q: Explain why a bridge rectifier would be used instead of a two-diode full-wave rectifier. In a…

Q: A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of 2KΩ i. Draw…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kN. a.…

A: In this question, We need to determine the dc average voltage Vdc? , PIV, maximum current rating…

Q: The rectifier below is operating at a frequency of 60 Hz, and the RMS value of the transformer…

A: As per our policy i have attempted only first three sub-parts. Given data: V1=6.3 VR=0.5 ΩΔV=0.25 V…

Q: 2. A single-phase single-diode (half wave) rectifier is connected to a 240 V, 50 Hz AC supply.…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: Derive the expression for average or dc voltage Vdc for a full-wave rectifier using time variable.

Q: Q2/ Determine the minimum input voltage required for regulation to be established in the figure.…

A: Whenever zener diode is in breakdown at the time output voltage will be constant that is equal to…

Q: Q4. In the full-wave diode rectifier shown below, the diodes are ideal. The source voltage is v, =…

Q: Explain the application of Zener diodes in industrial and power electronics based on its operating…

A: Zener diode is basically like an ordinary PN junction diode but normally operated in reverse biased…

Q: What is the value of angle of conduction for half and full wave rectifier. Derive expression for it.

A: An device which convert alternating signal in to pulsating direct signal is known as rectifier. The…

Q: The breakdown voltage of a standard signal diode is not sufficient for power applications. How is…

Q: Define the main difference between a rectifier diode and a Zener diode? What is their difference in…

A: To describe the difference between rectifier diode and zener diode along with their difference in…

Q: 1. Describe what will happen to the output voltage and PIV of a center-tapped full wave rectifier if…

A: Solution-1) In the centered tapped full-wave rectifier, mainly two diodes are used. This two…

Q: Q/ Explain the diode bias methods with drawing a simple circuit and draw the properties diagram

A: Biasing of PN junction Diode with simple circuit and properties diagram (V-I characteristics):

Q: A full-wave Bridge rectifier with 120 V-rms sinusoidal input has a load resistor of 1 kn. (a) If…

Q: Figure shows an AC source G having an effective voltage of 240 V, 60 Hz is connected to a…

A: Let us assume, that a constant current I0 flows through the given RL load. Calculate the dc output…

Q: A full-wave bridge rectifier with a 12V (pk) sinusoidal input has a load resistor of 20 k. (a) If…

A: given that Peak voltage Vm= 12 VRMS Voltage VRMS =122 = 8.48V (a) now…

Q: Since the power of the rectifier circuit is given by Vs = 300 sin(wt -n/2) volts and the four diodes…

Q: ww

A: Since the diode voltage is given as 0.6 V, the full-wave rectifier is shifted by 1.2 V. The voltage…

Q: Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply…

A: Explanation: a) In the semi converter rectifier with RL load we use two diodes and two SCRs. Let Vs…

Q: Q1 Drive an expression for the average output voltage on RL load for single phase full controlled…

A: Not required

Q: 5. Suppose we are given a pn diode, and we apply the applied voltage Va to the n-type and ground the…

A: Generally, the characteristics of p-n junction diode is, This characteristics is obtained when p is…

Q: 3) With reference to the illustration given below, with detailed explanation discuss about the…

A: According to the given question, it is required to explain the reverse recovery time and it's…

Q: A simple voltage regulator is shown in the figure below. The source voltage Vs varies from 8 to 12…

A: Given : [Vsmin,Vsmax]=[8,12] [iLmin,iLmax]=[50mA, 150 mA] VL= 5V

Q: A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 k_. (a) If…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A simple voltage regulator is shown in the figure below. The source voltage Vs varies from 8 to 12…

A: Given : Vs= [MIN, MAX]=[8, 12 ] IL=[MIN,MAX]=[50 mA, 150 mA] VL=5 V

Q: 2. What are the advantages of using cascade voltage regulator circuit? 3. To stabilize a voltage of…

A: 1)The Question Doesn't have any graph. 2)Advantages of Using Cascade voltage regulator circuit: They…

Q: Q1- What is the value of the threshold voltage Vth in forward bias ? Q2- Under what condition does…

A: In this question , we will find the value of threshold voltage in forward bias... Note:- due to…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of I kn. a.…

A: In this question, We need to determine the dc voltage at the load? PIV, maximum current through…

Q: The half-wave rectiﬁer as shown is operating at a frequency of 60Hz, and the rms value of the…

A: Given data, The value of rms voltage is Vrms = 12.6±10% V. The value of operating frequency is f =…

Q: 5. A single-phase diode bridge rectifier is supplying a load of 100 2. A capacitor needs to be…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 4) Consider the half-wave rectifier circuit shown below. The ac input voltage to the circuit is a 60…

A: Circuit Vrms = 6.3 = Vm2Vm = 6.32c = 47 mF , Rl = 10Ω(a) Peak o|p voltage across load RL→During…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1 kſN. a.…

A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q: Sketch circuits or diagrams for:- i. Half Wave Rectifier & its Output Rectified Waveform ii.…

A: a) Half Wave Rectifier & its Output Rectified Waveform

Q: A 6.3V AC signal is half-wave rectified and applied to a 33-ohm load resistance. Determine the peak…

Q: Consider the full wave rectifier circuit shown below, with a large smoothing capacitance C= 300µF…

A: Given:- Rl=1KVm=15VC=300μFrs=10ohmVf=0.7V

Q: Q3: Determine Vout, PIV and Ripple factor for the following circuit considering Ideal and practical…

A: Assume the turns ratio is 10:1 ; fin =60 Hz Peak primary voltage Vp(primary) = 2 x 150 = 212.13 V…

Q: For the full wave rectifier circuit shown, if Vs=15sin(120nt) (V), R=10o11, assuming constant…

A: This is full wave bridge rectifier.. Draw the source and output waveforms Average current and peak…

Question

Consider the half-wave rectifier shown in the figure below. Let v_s be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with V_{D = 0.7 V.}

Consider the half-wave rectifier circuit shown in the figure boclow. Let Ug be a sinusoid with
10V peak amplitude with frequency of 60 Hz, and let R = 1 k2. Use the constant-voltage-
drop diode model with Vp = 0.7 V.
え。
%3D
D.
R
kuf
27f =
VSE
Figure 1: Question2 Rectifier Circuit

(a) Sketch the transfer characteristic function of vo vs US-
(b) Sketch the waveform of uo on the same graph with vs over at least two (2)
cycles of us
(c) Find the peak current through the resistor R
(d) Sketch the output waveform vo if a capacitor C is connected in parallel with
R.
(e) Calculate the value of the capacitor C that will ensure that the voltage
peak voltage and lowest voltage is no greater that 10% of the peak voltage

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
If a diode full wave rectifier circuit is excited by an ac source with an amplitude of 10 V and angular frquency of 100 rad/sec, then what will be the amplitude of the dc voltage obtained at the output of the rectifier? Assume no filter circuit is used.
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
A number of diodes rated at 1620 V each are to be connected in series in a rectifier circuit with a maximum voltage of 3000V. A de-rating factor of 15% is recommended. The maximum difference in leakage current of the diodes is given as 10mA , and the maximum difference in stored charge is 20µC. Calculate, 1) the number of diodes that must be used, 2) a suitable component value for the static equalization circuit; 3) a suitable component value for the dynamic equalization circuit.
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
A single phase diode bridge rectifier has an input voltage of 240V and supplies a resistive load with a constant dc current of 10A. (a) Sketch a well labeled circuit of the rectifier described above.(b) Sketch the waveforms for the input voltage, output voltage, input current and output current. (c) Determine the maximum input voltage. (d) Load resistance. (e) Derive an equation for the average output voltage and calculate its value. (f) Derive an equation for the RMS value of the output voltage and calculate its value. (g) Determine the power dissipated in the load
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.
Derive the expressions for the ripple voltage and DC voltage of capacitor filterhalf-wave rectifier and capacitor filter full-wave rectifier.