A FW rectifier is required to deliver 48VDA with 10% ripple on a 7.5Ω resistor. a)Identify the capacitor providing these values (capacitance and ripple current - ripple current). b)Identify the necessary welding transformer for 120VAA 60Hz welding.c) Find the required serial inductance value for continuous current withdrawal from the source

A FW rectifier is required to deliver 48VDA with 10% ripple on a 7.5Ω resistor. a)Identify the capacitor providing these values (capacitance and ripple current - ripple current). b)Identify the necessary welding transformer for 120VAA 60Hz welding.c) Find the required serial inductance value for continuous current withdrawal from the source

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 3PA: An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80...

See similar textbooks

Similar questions

An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80 amp-hours each to provide battery backup for their computers. The lead-acid cells are to be replaced with nickel-metal hydride cells with a capacity of 40 amp-hours each. How many nickel-metal hydride cells will be required to replace the lead-acid cells and how should they be connected?
A FW battery rectifier charges a 12V battery. Identify the transformer providing 0.2Ω series resistance, 10A current for 120VAA welding (Number of turns and kVA rating). Find the efficiency of the circuit for 1.4 V diode transmission voltage.
Calculate the percent ripple for the voltage developed across a 120-microFarad filter capacitor when providing a load current of 80 mA. The full-wave rectifier operating from the 60-Hz supply develops a peak rectified voltage of 25 V.
A two-zone DC chopper with a DC input voltage of 200 V and a switching frequency of 20 kHz The energy of a 2 mH inductance with 100 A passing through it is transferred to the DC source. are transferred. Ignoring circuit losses, for λ = 2/5 a) Calculate the transmission times of the transistor and diode with the period. b) Find the amount of increase and decrease of inductance current in a period. c) Calculate the amount of energy transferred from the inductance in the first period. d) Find out in how many periods and in how many ms all the energy is transferred
Half-wave 50Hz sinusoidal uncontrolled rectifier circuit with a peak voltage value of 100V and a source inductance of 8mH is feeding a highly inductive load of 8A. The average value of the output voltage and power delivered are, respectively and what is the communication angle (u) Power Electronics
A half-wave rectifier with a reservoir capacitor is connected to an AC mains supply(220Vrms, 50Hz) via a 20:1 transformer. What value of the capacitor is needed forthe ripple voltage of X% of the peak input voltage? The load takes a maximum currentof ???? mA. X= 12% mA = 160
I need some help with this problem. I need to create a power supply from 110v 60hz to regulated an output between 6 and 9 v. the image is the desire circuit to acomplish the possible solution. The resistor after the bridge rectifier will work as a surge protector or current limiter for the zener diode. the other is the Load resistor. I need some sort of calculations to prove the specific values for the components to operate according to the specs that I already explain. I know the capacitor will smooth the ripple voltage etc... but I need some guidance to get actual values
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
Design rectifier circuits to provide an output of 100 VDC using:a) Half wave rectifierb) Center-tapped Full wave rectifier For each circuit, calculate the diode PIV ratings and the transformer turns ratio (secondary to primary), if power is taken from the 220 V line AC supply.Use Silicon diodes.
A silicon pn junction has the following doping condition: 10^(16)cm³ at n-type side and 10^(17) cm at p-type side.calculate total depletion width W, widths of depletion regions at p and n sides of the junction.where Vbi=0.754v Emax=0.0000165v/m
Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.
A silicon pn junction employs NA = 2 × 1016 cm−3 and ND = 4 × 1016 cm−3. Determine the built-in potential at room temperature (T = 300 K).