(a) Given two sequences x[n] = [1,2,3,4,5,6] and y[n] = [4,5,6,1,2,3]. It is known that 2πmno 6 Y[m] = X[m]e . Find two values of no consistent with this information. (b) Let X [m] be the 8-point DFT of the sequence x[n] = [1, −1, 2, 3, −3, 0, 0, 0]. Let y[n] be 2πmno 6 a finite length sequence whose DFT Y [m] is related to X[m] as Y[m] = X[m]e where no = 3. Determine the sequence y[n]. (c) Let X[m] be the 6-point DFT of x[n] = [1,2,3,4, 5, 6]. Determine the sequence y[n] whose DFT Y[m] = X[{{−m))6]. (d) Let X[m] denote the 80-point DFT of x[n], 0 ≤ n ≤79. The sequence x1[n] is obtained by zero-padding a[n] to length 128. Determine mo such that Y[8] = X[mo]. (e) Let X[m], (0 ≤m ≤ 20) and Xd(w) respectively be the 21-point DFT and DTFT of a real-valued sequence {n}7-0 that is zero-padded to length 21. Determine all the choices that are definitely correct, - 4π 21 • X[19] = Xa( - • X[2] = X(- 4π 21 • X[12] = X( 4π - 21 • X[4] = X(-11) 21

(a) Given two sequences x[n] = [1,2,3,4,5,6] and y[n] = [4,5,6,1,2,3]. It is known that 2πmno 6 Y[m] = X[m]e . Find two values of no consistent with this information. (b) Let X [m] be the 8-point DFT of the sequence x[n] = [1, −1, 2, 3, −3, 0, 0, 0]. Let y[n] be 2πmno 6 a finite length sequence whose DFT Y [m] is related to X[m] as Y[m] = X[m]e where no = 3. Determine the sequence y[n]. (c) Let X[m] be the 6-point DFT of x[n] = [1,2,3,4, 5, 6]. Determine the sequence y[n] whose DFT Y[m] = X[{{−m))6]. (d) Let X[m] denote the 80-point DFT of x[n], 0 ≤ n ≤79. The sequence x1[n] is obtained by zero-padding a[n] to length 128. Determine mo such that Y[8] = X[mo]. (e) Let X[m], (0 ≤m ≤ 20) and Xd(w) respectively be the 21-point DFT and DTFT of a real-valued sequence {n}7-0 that is zero-padded to length 21. Determine all the choices that are definitely correct, - 4π 21 • X[19] = Xa( - • X[2] = X(- 4π 21 • X[12] = X( 4π - 21 • X[4] = X(-11) 21

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a circuit that can detect the sequence '101101' anywhere in input, and outputs as 1 in that case. Consider overlapping in this scenario. Perform the following tasks: 1. Draw the state diagram. 2. Implement the State Table.
A particular interconnection between two logicgates in an IC chip runs one-half the distance acrossa 7.5-mm-wide die. The interconnection line is insulated from the substrate by silicon dioxide. If theline is 1.5 m wide and the oxide (εox = 3.9εoand εo = 8.85 × 10−14 F/cm) beneath the line is1 m thick, what is the total capacitance of thisline assuming that the capacitance is three timesthat predicted by the parallel plate capacitance formula? Assume that the silicon beneath the oxiderepresents a conducting ground plane.
Predict output of a microcontroller with its port P0 connected to LEDs based on the following program. Give your own analysis for each line of the program. BACK: MOV A, #55H MOV P0, A ACALL DELAY MOV A, #0AAH MOV P0, A ACALL DELAY SJMP BACK DELAY: MOV R3, #200 HERE: DJNZ R3, HERE RET
Q2. Design a digital circuit that indicates via an LED output whether a 4-bit unsigned number is a Lucas number (TRUE=1) or not (FALSE=0) (see Wikipedia). In this question, the input to the circuit should be assumed to be from a decimal keypad (0-9). Therefore, the behaviour of the circuit does not matter when then the input value is greater than 9. This should be taken advantage of in the design process. The steps are:(a) State the truth table for the circuit.(b) State the Karnaugh map for the circuit.(c) Group the 1-cells according to the Karnaugh map technique.
FIND BETA,, S,, S',, Find S'' , using T1 as the temperature at which the parameter values are specified and beta( T2 ) as 20% more than beta( T1
Consider two systems one is second order and the other is third order. The characteristic equations are: as2+bs+c for the second order and as3+bs2+cs+d for the third order, where a,b,c,d are positive real numbers. Then which of the following is correct with regard to the stability of these two systems? a. stability of either system cannot be confirmed with the given data b. third order is definitely stable but second order cannot be confirmed c. both systems are definitely stable d. second order is definitely stable but third order cannot be confirmed
1)The function L (x, y, z) given the truth table a) Write algebraically in the 1st canonical and 2. canonical expansions separately,b) Write in numerical form in the 1st canonical and 2.canonical expansions form,c) Perform the function with 2x1 MUX as y input is the selection input. 2)Obtain 4x1 MUX by using 2x1 MUX. Write down the table.
The answer of this question on bartleby is of other parts. This is different question. Don't copy that answer. I already have that. I am posting it for the third time. A. Write the state variable equation(s) B. The system equation(s) you obtained in D are (Circle one choice for each statement): Ordinary Differential Equation(s) True False Linear True False Second Order True False Constant Coefficients True False
Kindly assume the data which is not visible to you. But mention your assumption in the solution.
Design a circuit that can detect the sequence ‘101101’ anywhere in input, and that outputs as 1 in that case. Consider overlapping in this scenario. Perform the following tasks: ⦁ Draw the state diagram ⦁ Implement the State table
Compare the performances of the first order system, the overdamped, underdamped and critically damped second order system.
If x(n)=(0,0,1,2,3,4,0,0) then x(n-2) is?a. (0,0,2,4,6,8,0,0)b. (0,0,1,2,3,4,0,0)c. (1,2,3,4,0,0,0,0)d. (0,0,0,0,1,2,3,4)