A glass door is used on a fireplace to reduce exfiltration of room air through the chimney. The door, 0.70m high and 1.00m wide, reaches a uniform temperature of 232oC. If the room air temperature is 23oC, estimate the rate of heat transfer to the room air due to convection. Air properties: k=0.0338W/m-K ν=26.4x10-6 m2/s Pr=0.690

A glass door is used on a fireplace to reduce exfiltration of room air through the chimney. The door, 0.70m high and 1.00m wide, reaches a uniform temperature of 232oC. If the room air temperature is 23oC, estimate the rate of heat transfer to the room air due to convection. Air properties: k=0.0338W/m-K ν=26.4x10-6 m2/s Pr=0.690

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.41P

See similar textbooks

Similar questions

An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
A 5.0-cm-diameter cylinder is heated to a temperature of 200 oC, and air at 30 oC forced across it at a velocity of 50 m/s (h = 180 W/m2K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 oC. Comment on your calculation. COMPLETE SOLUTION
4.) A 15-cm-diameter steam line carries saturated steam at 6 MPa and is located in a tunnel with stagnant air with a temperature of 50oC. The outside unit convective coefficient is 8.5 W/m2-K. The steam line is covered with 3 cm of 85% magnesia insulation. It is decided to reduce the heat loss by one-half. How much 85% magnesia insulation is required? Neglect thermal resistance of pipe and inside surface.
Calculate the heat losses per unit length in a horizontal tube with an outside diameter of 15 cm, if its surface is kept at 400 K AND the surrounding air has a temperature of 300 K and a pressure of 1 bar.The properties of air at a pressure of 1 bar and a film temperature of 350 K are: In this case, v = 20.76 x 10-6 m2/s , α = 0.2983 x 10-4 m2/s, k = 0.03003 W/mK, Pr = 0.697, β = 2.86 x 10-3 K-1
A 5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a velocity of 50 m/s (h = 180 W/m2 K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 °C. Comment on your calculation.
A transformer is to be cooled via forced air convection. To increase the effectiveness of thecooling, Alloy 1095 cast aluminum fins are attached to the top of the transformer overwhich air is blown (negligible thermal contact resistance between the transformer and thefins). The fins are 2 cm thick and 7 cm long and span the entire length of the transformer,and the transformer is 7 cm wide and 10 cm long. Air leaves the cooling fan at 25°C .a) Decide how to model the fins before performing any real analysis. Youare willing to accept some error in your analysis and so you will either model thefins as having adiabatic tips or being infinitely long. You expect the average convectioncoefficient over the heat transfer surfaces for this system to be around 50 W m2– K⁄ .Which tip condition should you use for the fins in your analysis? b) Modeling the transformer as being isothermal, determine the average convectioncoefficient over the heat transfer surfaces. Account for heat transfer from the…
A long steel rod 0.305 m in diameter is initially at a temperature of 588 K. It is immersed in an oil bath maintained at 311 K. The surface convective coefficient is 125 W/m2 -K. Calculate the temperature at the center of the rod after 1 h. The average physical properties of the steel are k = 38 W/m-K and α = 0.0381 m2/h.
A 10 cm outer diameter pipe carrying saturated steam at a temperature of 195C is lagged to 20 cm diameter with magnesia and further lagged with laminated asbestos to 25 cm diameter. The entire pipe is further protected by a layer of canvas. If the temperature under the canvas is 20°C, find the mass of steam condensed in 8 hrs on a 100m length of pipe and interface temperature. Take thermal conductivity of magnesia as 0.07 W/m – K and that of asbestos as 0.082 W/m – k. Neglect the thermal conductivity of the pipe material. The latent heat of steam for given conditions can be taken as 1951 kJ/kg–K.
NUMBER 3 A food product with 80% moisture content in a 10 cm diameter can wants to be frozen. The density of the product is 1000 kg / m³, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -2.5 ° C. After 8 hours in the freezing medium -40 ° C, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder. h = W / (m² K).
A 15 cm outer diameter steam pipe is lagged to 25 cm diameter with magnesia of thermal conductivity 0.05 W/mK and further lagged with 30 cm diameter laminated asbestos of thermal conductivity 0.07 W/mK. Inner temperature of steam is 200° C and outer temperature is 25° C. Calculate the mass of steam condensed per hour for 120 m length of pipe. Assume latent heat of steam is 1900 kJ/kg.