A group of twelve prestressed concrete piles is to support a building column. The total downward design load on the group is 4,900 k. Assuming this load is evenly distributed across the 12 piles, and that there are no moment or shear loads, select a pile size and 28-day compressive strength of the concrete.

A group of twelve prestressed concrete piles is to support a building column. The total downward design load on the group is 4,900 k. Assuming this load is evenly distributed across the 12 piles, and that there are no moment or shear loads, select a pile size and 28-day compressive strength of the concrete.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.5P: A 400 mm 400 mm square precast concrete pile of 15 m length is driven into a sand where = 18.0...

See similar textbooks

Similar questions

Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
A 500 mm square prestressed concrete pile is to driven 19 m into the soil profile shown in figure. Compute the net ultimate toe-bearing capacity. Water table is 3 m.Calculate the ultimate load capacity. FS = 3
Q3: A group of 12 piles with 3 piles in a row was driven into a soft clay extending from ground level to a great ‎depth. The diameter and the length of the piles were 40 cm and 12 m respectively. The unconfmed ‎compressive strength of the clay is 50kPa. If the piles were placed 100 cm center to center, compute the ‎allowable load on the pile group on the basis of a shear failure criterion for a factor of safety of 2.5. ‎ *
a 15-meter precast concrete pile is to be lifted. if the unit weight of concrete is 23.54 kN/m3. And the section of the pile measures 400 mm by 400 mm.
A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven into clay having an unconfined compressive strength of 180kPa and the unit weight of clay is 18kN/m3. The spacing of piles is 0.75m center to center. Assuming a bearing capacity factor of Nc = 9, a= 1.0. Which of the following most nearly gives the minimum pile spacing in order to achieve 100% efficiency?
Determine the ultimate bearing load of the pile using Tomlinson for a 12.5-m closed-end steel pipe pile is driven into a uniform undrained clay. Pile diameter = 0.5 m. Unit weight of clay is 18.5 kN/m3, and undrained cohesion of 95 kN/m2. The groundwater table is at the ground surface and the clay layer extends to a great depth.
A concrete pile 20 m long with a cross section of 400 mm x 400 mm is fully embedded in a saturated clay layer. The clay has the following properties: γsat = 18.5 kN/m3, ϕ= 0 and cu = 70 kPa. Assume that the water table rises to the tip of the pile. Determine the allowable load that the pile can carry (FS=3). Use the α and λ method to estimate the skin resistance.
A reinforced concrete pile weighing 30 kN is driven by a drop hammer weighing 40 kN and having an effective fall of 0.8 m. The average set per blow is 1.4 cm. The total temporary elastic compression is 1.8 cm. Assuming the co-efficient of restitution as 0.25 and a factor of safety 2, determine the ultimate bearing capacity and the allowable load for the pile using Hiley’s formula.
Q4) The ultimate load capacity of a 10 m long concrete pile of square cross section 500 mm x 500 mm driven into a homogeneous clay layer having undrained cohesion value of 40 kPa is 700 kN. Determine the ultimate load capacity if the cross section of the pile is reduced to 250 mm x 250 mm and the length of the pile increased to 20m.
2. A 40 cm diameter pile carries an allowable load of 200 kN with unit weight of 19 kN/m3 and cohesion of 48 kPa. determine the following:(a) Lengthofthepile.(b) Unconfined compressive strength.
A 30 cm diameter concrete pile is driven in a normally consolidated clay deposit 15 m thick. Estimate the safe load. Take cu = 70 kN/m^2 , α= 0.9 and FS= 2.5 . [Ans, 375 kN]
A concrete pile, 350 mm square, is driven into a thick deposit of medium sand with φ= 35° and ϒ = 19kn/m3. The water table lies at 2.0 m below ground level. Estimate the length of pile required to support a working load of 450 KN assuming a an overall factor of safety of 2.5. I will report and downvote wrong answer