A group pile has a section of 4 x 4 with each having a diameter of 305 mm are embedded in clay. The length of the piles are 12 m and the spacing between the piles (d) are 1.0 m. The recorded soil profile for the ground is shown in Table 1. Propose the allowable load bearing capacity of the pile with a factor of safety of (FS) of 3. (b)

A group pile has a section of 4 x 4 with each having a diameter of 305 mm are embedded in clay. The length of the piles are 12 m and the spacing between the piles (d) are 1.0 m. The recorded soil profile for the ground is shown in Table 1. Propose the allowable load bearing capacity of the pile with a factor of safety of (FS) of 3. (b)

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.10P

See similar textbooks

Similar questions

Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure 18.36, with a safety factor of 3. Use the a method for computing the shaft friction. FIG. 18.36
Redo Problem 18.10 using the method for estimating the skin resistance. 18.10 A concrete pile 15 m long with a cross section of 380 mm 380 mm is fully embedded in a saturated clay layer. For the clay, sat = 18 kN/m3, = 0, and cu = 80 kN/m2. Assume that the water table lies below the tip of the pile. Determine the allowable load that the pile can carry (FS = 3). Use the a method to estimate the skin resistance.
In a piled raft, 450 mm diameter and 13 m long piles are placed in a rectangular grid at 1.60 m 1.63 m spacing. Find the pile-raft interaction factor assuming uniform soil conditions with depth and
A 400-mm diameter and 15 m long concrete pile is driven into a sand where = 18.0 kN/m3 and = 31. Assuming = 0.65 and K = 1.4 Ko, determine the load carrying capacity of the pile with a factor of safety of 3.
A 300 mm diameter steel pipe pile with 10 mm wall thickness is to be driven to a depth of 15 m in a stiff clay having ET = 100 MPa. The side friction capacity, ΣfnAs, is 750 kN and the toe bearing capacity, q'nAt, is 210 kN. The expected service load will be 310 kN. Using the Fleming simplified method, compute the expected settlement. Assume fn is constant along the length of the pile.
5 A group of 9 piles of 28 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.11 m. The length of the piles is 13 m. Unit cohesion of the clay is 94 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.72. Round off to two decimal places.
A group of 9 piles of 29 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.01 m. The length of the piles is 12 m. Unit cohesion of the clay is 80 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.69.
A concrete pile 50 ft long having a cross section of 15 in. x 15 in. is fully embedded in a saturated clay layer for which γsat = 121 lb/ft3, Φ = 0, and cu = 1600 lb/ft2. Determine the allowable load that the pile can carry. (Let FS = 3.) Use the a method Eq. (9.59) and Table 9.10 to estimate the skin friction and Vesic’s method for point load estimation.
A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven into clay having an unconfined compressive strength of 180kPa and the unit weight of clay is 18kN/m3. The spacing of piles is 0.75m center to center. Assuming a bearing capacity factor of Nc = 9, a= 1.0. Which of the following most nearly gives the minimum pile spacing in order to achieve 100% efficiency?
A rectangular pile (0.91 x 0.54 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 5 m., cohesion of 51 kPa, friction factor of 0.82. Second layer has a height of 5 m., cohesion of 71 kPa, and friction factor of 0.84. Compute the allowable load that the pile can carry if the factor of safety is 2.97