A hollow steel cylinder (length l=300mm) inside diameter d=150mm wall thickness t=3mm is filled with concrete and compressed between rigid plates by load P=500KN, find the stresses and the shortening of the cylinder if Es=200KN/mm for the steel and Ec =20KN/mm for the concrete?

A hollow steel cylinder (length l=300mm) inside diameter d=150mm wall thickness t=3mm is filled with concrete and compressed between rigid plates by load P=500KN, find the stresses and the shortening of the cylinder if Es=200KN/mm for the steel and Ec =20KN/mm for the concrete?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.1P: An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The...

See similar textbooks

Related questions

Q: A nonprismatic bar ABC made up of segments AB (length Lị . cross-sectional area S1) and BC (length…

A: Given:- AB=L1 Area of AB=S1 BC=L2 Area of BC=S2 Modulus of elasticity=E Elasticity length=L3 Spring…

Q: Task 2 In the shown Figure 2, a cylindrical pressure vessel of radius r= 36 cm and thickness t = 5…

A: Solution: Stress acting on the point A along x-axis Longitudinal stress due to internal pressure of…

Q: A hollow, brass circular pipe ABC (see figure) supports a load P1=26.5kips acting at the top. A…

A: *According to hooks law , Stress = E * strain , where E is modulus of elasticity . * Poisson…

Q: Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below.…

Q: A trimetallic bar is uniformly compressedby an axial force P = 9 kips applied through a rigidend…

Q: A pressurized steel tank is constructed with a helical weld that makes an angle at = 55" with the…

A: Stress and strain Strain is the response of a system to an applied stress. When a material is…

Q: A rod is composed of three segments, as shown in the figure. Compute the stress induced in each…

A: Given: temperature drop =30oC To determine: Stresses in each material a) if walls are rigid b)…

Q: A prismatic bar AB with a solid circularcross section (diameter d) is loaded by a distributedtorque…

Q: 10. A steel rectangular block, a = 2.4cm wide and b =1.2 cm deep, is subjected to an axial tensile…

A: GIVEN :- Width : a=2.4 cm=0.024 mdepth : b=1.2 cm=0.012 mLength : L=10 cm=0.1 mincrease in length :…

Q: In the shown Figure 2, a cylindrical pressure vessel of radius r = 42 cm and thickness t = 6 mm is…

A: Given data: The radius of the pressure vessel is r = 42 cm. The thickness of the pressure vessel is…

Q: A simply supported beam -b<y<b, 0 <x<L, as shown below, is subjected to a compressive load of half…

A: σy= -3 4bx δ2Mδx2[y33b2-y] +c3f(x)+c4σy=0 at uy=-bc3f(x)+c4=34 δ2Mσx2 x 23= σy=-3…

Q: A thin-walled circular tube and a solid circular bar of the same material (see figure) are subjected…

Q: 1) Steel railroad reels 10 m long are laid with a clearance of 3 mm at a temperature of 15°C. At…

Q: A Belleville spring is made of silicon steel. The spring is compressed completely fl at when it is…

A: Given Force = 4500 N Allowable stress = 1375 × 106 N/m2 do/di =1.75 h/t = 1.5 To find Thickness of…

Q: A rail line is laid so that there is no stress in rails at 15°C. The rails are 50 m long. α = 11.7 ×…

A: Temperature, T1= 15∘C Rail length, L= 50 m α= 11.7×10-6/∘C E= 2.3×105 N/mm2 Expansion allowance, ∆=…

Q: A standard brick (dimensions 8 in. 3 4 in. 32.5 in.) is compressed lengthwise by a force P, as…

A: Given Shear stress = 1200 psi Compressive stress = 3600 psi Find Maximum load, Pmax

Q: A rod is composed of three segments, as shown in the figure. Compute the stress induced in each…

A: Part (a) Write down the given values for the bronze rod. Here Eb signifies bronze young modulus, αb…

Q: A 3.0 m long brass pipe is subjected to the weight 'P' of 1000 kg as shown in figure below.…

A: Given, Eccentric load, P=10000NEccentric distance, e=5mmLength of pipe, L=3mExternal diameter of…

Q: 1.An axial pull of 40000 N is acting on a bar consisting of three sections of length 30 cm,25 cm and…

Q: A rigid strut ABCD supports two concentrated loads P at points B and D. It is being supported by a…

A: Given: The area of cable, A = 120 mm^2 = 120 x 10-6 m2 The elastic modulus of the cable, E = 50 GPa…

Q: A round steel pipe of inside diameter d=500 mm and wall thickness t=12 mm is filled with concrete…

Q: The system in the figure is carried by a 50 mm diameter column. If the modulus of elasticity of the…

A: Given, The diameter of column, d = 50 mm Modulus of elasticity, E = 70 GPa The length of column, L =…

Q: A plastic bar of diameter d = 51 mm is to be twisted by torques T (see figure) until the angle of…

A: Given: d = 51 mm angle of twist = 4 o To find: a) If Shear strain = 0.011 rad then L max = ?…

Q: A circular bar, with shear modulus 40 GPa and radius 10 mm, is subjected to torques at points A, B,…

Q: A closed thin walled cylindrical vessel has a diameter D of 660 mm, a wall thickness t of 2.0 mm and…

Q: Simple Stress and Strain Question 2 At short, reinforced cement concrete column 600 mm x 600 mm has…

A: To find: The stress in steel, concrete and elastic shorting of the column. Given: The size of the…

Q: A hemispherical window (or viewport) in adecompression chamber (see figure) is subjected toan…

A: Given data as per question Internal air pressure = 85 psi Number of bolts =14 The radius of the…

Q: A square plate of dimension Lx Lis subjected to a uniform pressure load p 250 MPa on its edges as…

A: Given:Square plate of L×Luniform pressure load, p=250 MPaE=200 GPaL=2 mδ=0.001 m

Q: a steel clamped manhole cover, subjected to uniform load Po, consists of a flat plate reinforced by…

A: In order to limit distortion during the machining process, clamping devices are utilized. Once the…

Q: A thin-walled cylindrical pressure vessel of a radius r is subjected simultaneously to internal gas…

A: Given Force, F = 190 kN Internal pressure p = 12 MPa Inner diameter, d = 200 mm…

Q: he beam supports an 80 kg vertical mass applied at D. The beam is pinned to the wall at point A and…

A: Here, BC=15cm×15cm E=70GPa Load at D, FD=80×g=80×9.81N=784.8N Taking moment about point A. ∑MA=0…

Q: A closed thin walled cylindrical vessel has a diameter D of 100 mm, a wall thickness t of 8 mm and…

Q: A thin-walled cylindrical pressure vessel of radius r is subjected simultaneously to internal gas…

Q: A rail line is laid so that there is no stress in rails at 15°C. The rails are 500000 mm long. α =…

Q: A flexible connection consisting of rubber pads (thickness t 5 9 mm) bonded to steel plates is shown…

Q: A steel clamped manhole cover, subjected to uniform load Po, consists of a flat plate reinforced by…

A: When a load is applied to a material or structure it tends to bend or deform due to the stress…

Q: The rigid bar of negligible weight is supported as shown in the figure. If W=60 kN, compute the…

A: Force acting in the vertical direction is vA+Ts+TB=60⋯⋯⋯(1) Moment about point A is…

Q: Problem 1. For the grid shown in Figure below, determine the nodal displacements and the local…

A: Given: Let us consider the given data, E=30×106 psiG=12×106 psiI=200 in4J=100 in4d1y=ϕ1x=ϕ12=0d3y=0…

Q: 1. A force P = 27 kN acts on a round bar with d = 50 mm, find the stress in KPa. 2. The piston rod…

A: Answer: 1. The stress is 13751 kPa. 2. The compression of the piston rod is 0.0261 mm.

Q: Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw…

Q: 1,2 m -0,6 m Im Çap:50 mm The system in the figure is carried by a 50 mm diameter column. If the…

A: Solution: We need to find the critical load to prevent the column BC from buckling, since both ends…

Q: For thin walled pressure vessel: Inner radius =50 cm P' Wall thickness =3 cm P=P'= 0 kN Gage…

Q: An undeformable mass of 500 kg is suspended from a polyamide round cable (diameter 10 mm) in a low…

A: To find: The normal engineering stress. Given: The mass attached to the cable is m=500 kg. The…

Q: F4.A rectangular steel beam between two rigid walls, 96 in. apart, is heated to a uniform…

Q: A pressurized steel tank is constructed with a helical weld that makes an angle a = 55° with the…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Еx10:
A hollow steel cylinder (length l=300mm) inside diameter d=150mm wall
thickness t=3mm is filled with concrete and compressed between rigid plates by
load P=500KN, find the stresses and the shortening of the cylinder if
Es=200KN/mm for the steel and Ec =20KN/mm for the concrete?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 GIVEN

VIEW

Step 2 SOLUTUON

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ Pr
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (sec figure), The tank has a radius of r = 125 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 850 N m. (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 160 MPa? (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank?
-21 Plastic bar AB of rectangular cross section (6 = 0.75 in. and h = 1.5 in.) and length L = 2 Ft is Fixed at A and has a spring support (Ar = 18 kips/in.) at C (see figure). Initially, the bar and spring have no stress. When the temperature of the bar is raised hy foot. the compressive stress on an inclined plane pq at Lq = 1.5 Ft becomes 950 psi. Assume the spring is massless and is unaffected by the temperature change. Let a = 55 × l0-6p and E = 400 ksi. (a) What is the shear stresst9 on plane pq? What is angle 07 =1 Draw a stress element oriented to plane pq, and show the stresses acting on all laces of this element. (c) If the allowable normal stress is ± 1000 psi and the allowable shear stress is ±560 psi, what is the maximum permissible value of spring constant k if the allowable stress values in the bar are not to be exceeded? (d) What is the maximum permissible length L of the bar if the allowable stress values in the bar are not be exceeded? (Assume £ = IB kips/in.) (e) What is the maximum permissible temperature increase (A7") in the bar if the allowable stress values in the bar are not to be exceeded? (Assume L = 2 ft and k = L& kips/in
Solve the preceding problem for a W 250 × 89 steel column having a length L = 10 m. Let E = 200 GPa.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A cantilever beam(Z, = 6 ft) with a rectangular cross section (/> = 3.5 in., h = 12 in.) supports an upward load P = 35 kips at its free end. (a) Find the state of stress ((7T, o^., and r in ksi) on a plane-stress element at L/2 that is i/ = 8 in. up from the bottom of the beam. Find the principal normal stresses and maximum shear stress. Show these stresses on sketches of properly oriented elements. (b) Repeat part (a) if an axial compressive centroidal load N = 40 kips is added at B
A steel bracket of solid circular cross section is subjected to two loads, each of which is P = 4.5 kN at D (see figure). Let the dimension variable be b = 240 mm. Find the minimum permissible diameter dmaxof the bracket if the allowable normal stress is 110 M Pa. Repeat part (a), including the weight of the bracket. The weight density of steel is 77.0 kN/m3.
A pinned-and column of a length L = 2A m is constructed of steel pipe (E = 210GPa) having an inside diameter d1= 60 mm and outside diameter d2= 68 mm (sec figure). A compressive load p = 10 kN acts with eccentricity e = 30 mm. What is the maximum compressive stress max in the column? If the allowable stress in the steel is 50 MPa, what is the maximum permissible length Lmaxof the column?
Beam ABC with an overhang BC is subjected to a linearly varying distributed load on span AB with peak: intensity q0= 2500 N/m and a point load P = 1250 N applied at C. The beam has a width ft = 100 mm and depth h = 200 mm. Find the state of plane stress at point D located 150 mm below the top of the beam and 0.2 m to the left of point B. Also find the principal stresses at D>Neglect the weight of the beam.
A W410 × S5 steel column is compressed by a force P = 340 kN acting with an eccentricity e = 38 mm, as shown in the figure. The column has pinned ends and a length L. Also, the steel has a modulus of elasticity E = 200 GPa and yield stress y= 250 MPa. P = 340 kN If the length L = 3 m, what is the maximum compressive stress maxin (he column? If a factor of safety n =2.0 is required with respect to yielding, what is the longest permissible length Lmaxof the column?
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.