Task 2 In the shown Figure 2, a cylindrical pressure vessel of radius r= 36 cm and thickness t = 5 mm is subjected simultaneously to internal gas pressure of 1.2 MPa and a load P of 3 KN (Ignore the torque from load P). Let L = 0.7 m and find thex and y stresses at point a.

Task 2 In the shown Figure 2, a cylindrical pressure vessel of radius r= 36 cm and thickness t = 5 mm is subjected simultaneously to internal gas pressure of 1.2 MPa and a load P of 3 KN (Ignore the torque from load P). Let L = 0.7 m and find thex and y stresses at point a.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.10.1P: The flat bars shown in parts a and b of the figure are subjected to tensile forces P = 3.0 kips....

See similar textbooks

Related questions

Q: The bracket as shown in Figure Q4 is subjected to forces 750 N, 300 N and moment 500 Nm. The bracket…

Q: 3 For the plane trusses supported by the spring at node 1 in Figure P3–33 (a) and (b), determine the…

Q: "Prob. 3.3-10. A 12-ft beam AB that weighs W, 180 lb supports an air conditioner that weighs W, =…

A: Given that: Length of the beam = 12 ft = 144 in Wa = 1000 lb, Wb = 180 lb It is required to…

Q: The articular Cartilage is subjected to plane stress with normal stresses ox , Oy and shear stress…

A: Given data as per question Normal sress in x axis =3 Mpa Angle =300

Q: The flat bars shown in parts a and b of the figure are subjected to tensile forces P-3.0 kips. Each…

A: Given data, Tensile force P=3.0 Kips Thickness t=0.3 in.a For the bar with a…

Q: Figure Q3 shows stainless steel shaft consists of solid 40 mm diameter section (1), 30 mm diameter…

Q: A tank is in the form of an ellipsoid having the dimension as shown in figure a. It is fabricated…

A: Given: The thickness of ellipse, t = 5 mm The pressure inside the ellipse, P = 250 + 44 = 295 kpa…

Q: The hollow drill pipe for an oil well (see figure)is 6.2 in. in outer diameter and 0.75 in. in…

A: Given Outer diameter = 6.2 in Thickness = 0.75 in Weight = 62 kips Torque = 185 kip-in To find…

Q: A homogenous rigid block subjected to the loading shown in figure is supported by three steel rod…

A: Given: Diameter of steel rod, d=25 mm

Q: Q.3) For the shaft consist of two parts shown in figure. If shaft (1) has outside diameter doutl =…

Q: Problem 4 A cylindrical pressure vessel with radius r =200 mm and wall thickness t =10 mm is…

A: INTRODUCTION : Hydraulic cylinders, cannon barrels, pipes, boilers, and tanks are examples of…

Q: The cantilevered tube shown in the following figure is to be made of 2014 aluminum alloy and is…

A: The tube is subjected to axial loading, bending, and torsion simultaneously, thus there will be…

Q: A solid circular shaft of ABCD (having a fillet at B and a notch at D) is simply supported at points…

A: GIVEN :- F=15KN P=12KN RB=3mmRD=2mmSy=400MPa

Q: In the shown Figure 2, a cylindrical pressure vessel of radius r = 42 cm and thickness t = 6 mm is…

A: Given data: The radius of the pressure vessel is r = 42 cm. The thickness of the pressure vessel is…

Q: PROBLEM 2. The forces shown in the figure are applied to a plate connected to a pipe with an outer…

Q: As illustrated in Figure 1, the rectangular bar with dimensions of 250 mm by 400 mm is subjected to…

Q: Q2: One side of a petrol drill pipe, as shown in the figure, has been lifted with the use of a crane…

A: The cross-sectional diagram of the pipe is shown below.

Q: 1. A nitrogen gas storage tank produced by a company has a rotating cylindrical shell and standard…

Q: The pinned joint shown in the figure below is held by a ¾-in-diameter pin at A. If the force P = 5…

A: Given data :- diameter= 3/4 in Force(P) =5kips Thickness =1 in

Q: 3.33 For the plane trusses supported by the spring at node 1 in Figure P3-33 (a) and (b), determine…

A: As per our guidelines, we are supposed to answer only one question. Kindly repost other question as…

Q: Problem 4 A thin-walled cylindrical pressure vessel has an internal diameter of d = 2 m and a wall…

Q: For the plane trusses with inclined supports shown in Figure P3-51, solve for the nodal…

Q: Problem 2 For the wedge of unit thickness subjected to concentrated load, F (see the figure below),…

Q: 5. A brass pipe has an internal diameter of 400mm and a metal thickness of 6mm. A single layer of…

A: Given data: The internal diameter of the brass pipe is di=400 mm The thickness of the brass metal…

Q: If the stress distribution in the rectangular plate shown in the figure can be given by the Airy…

A: The given Airy stress function is : Φ = px3y + qxy3

Q: The machine component shown in Figure below is subjected to a load P = 450 lb that acts at an angle…

Q: A pressurized cylindrical tank with flat endsis loaded by torques T and tensile forces P (see…

A: Given data as per question The internal pressure p = 7.25 MPa Torque T =850 N .m. t = 6.5 mm

Q: 7.4-17 A sign is supported by a pole of hollow circular cross section, as shown in the figure. The…

A: Given: The outer diameter of pole, D = 10.5 in The inner diameter of pole, d = 8.5 in The height of…

Q: Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an…

A: 2 Given: The internal radius, ri = 50 mm The outer radius, ro = 130 mm The internal pressure, Pi =…

Q: A segment of a generator shaft is subjected to a torque T and an axial force P, as shown in the…

A: Given, P = 540 kN d1 = 250 mm d2 = 300 mm T = Po2πf=1800×1032×π×4=71620 N-m Area, A = π4(d22-d12) =…

Q: In the figure, the steel shaft with a diameter of 36 mm is 240 mm diameter pulley. Belts also formed…

Q: ..For the figure shown blow, if the temperature decrease by 40°C. find the stress in the Aluminuim…

Q: PROBLEM1. The figure shows a space quality hydrazine fuel tank designed by the Orbital Propulsion…

A: According to the given information, we have the length of the tank is 890 mm, the volume of the tank…

Q: A hemispherical window (or viewport) in adecompression chamber (see figure) is subjected toan…

A: Given data as per question Internal air pressure = 85 psi Number of bolts =14 The radius of the…

Q: A thin-walled cylindrical can with rigid end caps has a mean radius R = 100 mm and a wall thickness…

A: Given, Mean radius of can = R = 100 mm Wall thickness of can = t = 5 mm Additional tensile stress =…

Q: Problem C-2 [Average Normal and Average Shear Stresses] A structure is under an external loading of…

A: To normal and average stress at section aa

Q: In the crank arm of the figure, two loads P act as shown: one parallel to the x axis and another…

A: (a) Draw the given diagram with support reactions, Now, apply force equilibrium in x-direction,…

Q: 7. The uniform 150-kg bar AB shown in Figure 5 carries a 2KN vertical force at A. the bar is…

Q: Problem 2.3 A machine bracket is loaded with an inclined force of 1000 N as shown in the figure…

Q: Figure Q5 shows a thick cylinder of [A] mm intemal radius and [B] mm outer radius is subjected to an…

A: Given data: Inner Radius = A Outer Radius = B Internal Pressure = 60 MN/m2 External Pressure = 30…

Q: A thin cylindrical tank is subjected to an internal pressure (p) of 15 MPa and at the same time, is…

A: Calculate the shear stress applied on tank due to torque.…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

A: Given data, σpunching= Average punching shear stress in the collar = 100 MPa σbearing = Average…

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm…

A: Stress (σ) is defined the force per unit area.

Q: For the framc shown in the figure, Find the normal and shear stresses based on the following…

A: Given: The diameter of the pin at A, d = 10 mm The diameter of the pin at C, D = 15 mm

Q: For thin walled pressure vessel: Inner radius =50 cm P' Wall thickness =3 cm P=P'= 0 kN Gage…

Q: A segment of a generator shaft is subjected to a torque T and an axial force P, as shown in the…

A: Given that, d2=307 mm,d1=250 mm,Power delivered, Pd=1800 kW,Frequency, f=4 Hz, Calculate torque…

Q: The stresses at a point on the surface of a generator shaft are o =-50 MPa, o, = shown in Figure Q3.…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Task 2
In the shown Figure 2, a cylindrical pressure vessel of radius r = 36 cm and thickness t = 5 mm is
subjected simultaneously to internal gas pressure of 1.2 MPa and a load P of 3 KN (Ignore the
torque from load P). Let L = 0.7 m and find the x and y stresses at point a.

B
D
P
500 mm
Figure 2 Pressure Vessel with External Force
N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (sec figure), The tank has a radius of r = 125 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 850 N m. (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 160 MPa? (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank?
Solve the preceding problem if the stresses acting on element A on the web of a train rail (see figure part a of Problem 7.2-5) are found to be 40 MPa in tension in the horizontal direction and 160 MPa in compression in the vertical direction. Also. shear stresses of magnitude 54 MPa act in the direct ions shown in the figure. Determine the stresses acting on an element oriented at a counterclockwise angle of 520 from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
The stresses acting on element A in the web of a train rail are found to be 40 M Pa tension in the horizontal direction and 160 MPa, compression in the vertical direct ion. Also, shear stresses of magnitude 54 MPa act in the directions shown (see the figure b for Problem 7.2-5). Determine the principal stresses and show them on a sketch of a properly oriented element.
An element in plane stress is subjected to stresses sx= -5500 psi, sy= -2000 psi, and Tx. = 1900 psi (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an internal air pressure of 85 psi. The window is attached to the wall of the chamber by 14 bolts. (a) Find the tensile force Fin each bolt and the tensile stress (T in the viewport if the radius of the hemisphere is 14 in. and its thickness is 1.25 in. (b) If the yield stress for each of the 14 bolts is 50 ksi and the factor of safety is 3.0, Find the required bolt diameter. (c) If the stress in the viewport is limited to 500 psi, find the required radius of the hemisphere.
A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses in tension, compression, and shear arc 90 MPa, 70 MPa, and 40 MPa, respectively. Also, the allowable tensile strain is 220 x 10-6, Determine the minimum required diameter d of the bar, If the bar diameter d = 40 mm, what is Tmax?
A beam with a width h = 6 in. and depth h = 8 in. is simply supported at A and B. The beam has a length L = 10 ft and is subjected to a linearly varying distributed load with peak intensity q0= 1500 lb/ft. Calculate the state of plane stress at point C located 3 in. below the top of the beam and 0.1 ft to the left of point B. Also find the principal stresses on element C. Neglect the weight of the beam.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
An element in plane stress is subjected to stresses ??x= 5750 psi, sy = 1100 psi, and txy= 750 psi (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
The flat bars shown in parts a and b of the figure are subjected to tensile forces P = 3.0 kips. Each bar a has thickness t = 0.25 in. (a) For the bar with a circular hole, determine the maximum stresses for hole diameters d = 1 in. and d = 2 in. if the width b = 6.0 in. (b) For the stepped bar with shoulder fillets, determine the maximum stresses for fillet radii R = 0.25 in. and R = 0.5 in. if the bar widths are b = 4.0 in. and c = 2.5 in.