A hollow steel shaft shown in Figure. Find the lengths of the two portions if the angle of twist produced in the two portions of the shaft are equal and the shear stress is not to exceed 60 MPa. (hint: use max torque) * "I 800 mm

A hollow steel shaft shown in Figure. Find the lengths of the two portions if the angle of twist produced in the two portions of the shaft are equal and the shear stress is not to exceed 60 MPa. (hint: use max torque) * "I 800 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Related questions

Q: a) An alumium shaft shown in figure-2, has x-sectional area in the shape of equilateral triangle. if…

A: given data: for equilateral triangle : τallow=56MPa ,φallow=0.02rad Gallow=26GPa=26*103MPa side…

Q: A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

A: Find the outside and inside diameter .

Q: An alumium shaft shown in figure-2, has x-sectional area in the shape of equilateral triangle. if…

A: Write down the given values using suitable variables. Here τ signifies allowable shear stress, ϕ…

Q: 3.31 A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an i diameter of 1.5 in.…

Q: 3.33 The figure shows an inboard engine, 8-fN long steel drive shaft, and propeller for a motor…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: d Bronze B Steel - b–

Q: 3.2-1 A copper rod of length L 18.0 in. is to be twisted by torques T(see figure) until the angle of…

Q: QUESTION 8 A torque T is applied on an aluminium shaft acting at the ends (see figure). The shaft is…

Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…

Q: 1. See figure below and solve for the maximum value of torque the composite shaft can accommodate…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

Q: 3.5-2 The outer diameter of the hollow aluminum shaft (see figure) is d 2 =100 mm^ and the inner…

Q: For the cross-section shown below, computer the rate of twist and the shear stress if a torque of…

A: Torsion Torsion is a twisting of object when torque is applied on it. Torque Torque is a…

Q: A 55-mm-diameter solid circular shaft as shown in the figure is made up of an aluminum material. The…

A: Given; d= 55 mmτ= 75 MPaG = 29 GPaθA/C=0.065 rad

Q: 1. See figure below and solve for the maximum value of torque the composite shaft can accommodate…

A: For solution refer below images.

Q: T -1.5m Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 50ON.m as in…

A: Write the given data with suitable variables. d=30 mmL=1.5 m=1500 mm1000 mm1 mT=500 Nm=500000…

Q: Q2: For the shaft shown in Figure 2, find the maximum shearing stress in the Aluminum and the steel…

Q: A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as shown…

Q: Figure 2: cylindrical shaft

Q: The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques as shown in…

Q: 3.9 A square steel rod 20 mm on a side develops a tor- sional shear stress of 50 MPa when subjected…

A: Introduction: When the shaft rotates, shear stress is created in the shaft. The shear stress varies…

Q: A circular aluminum tube subjected to pure torsion by torques T (see figure 2) has an outer radius 2…

Q: A hollow steel shaft, 12 m long, is required to transmit 1000 kW when running at a speed of 300…

A: Given that , L=12m =12000mm P=1000 kW =1000×106N-mm/s

Q: A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in…

Q: Calculate the shear stress and the angle of twist (in degrees) for a thin-walled steel tube (G=76…

A: Given data: The modulus of rigidity, G=76 GPa. The length of the tube is, L = 1.5 m. The applied…

Q: A hollow shaft and a solid shaft constructed of the same material have the same length and the same…

A: In the given problem, radius of solid shaft and outer radius of hollow shaft is same i.e., R The…

Q: 3.30 A solid steel shaft transmits 20 hp while running at 120 rev/min. Find the smallest safe…

Q: 4. A round steel shaft rotates at 200 rpm while delivering 5000 W to a gear producing a bending…

Q: An aluminium hollow thin-wall torsion member shown in Fig. 3.15 is 3 m long. If a torque of 10 kN-m…

A: We know that a 3 m long aluminium hollow thin wall torison member is illustrated in the diagram.We…

Q: 3. From the figure shown below, determine the stress of member AB and BC. And calculate the maximum…

Q: 1 of 1 -1.5m- Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 500N.m…

Q: The composite shaft shown in the figure is manufactured by shrink-fitting a steel sleeve over a…

Q: 1. The solid line shaft in Fig. 1 is made of steel and transmits the input power of 35 kW at pulley…

A: The Answer is Below

Q: Example 1 A shaft is transmitting 100 kW at 160 rp.m. Find a suitable diameter for the shaft, if the…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: A hollow shaft and a solid shaft constructed of the same material have the same length and the same…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

Q: A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the…

Q: F3.A shaft is composed of two 6-in. diameter sections coupled together (see figure below). Part AB…

A: Introduction: A composite shaft is formed when two shafts of different materials are joined together…

Q: A shaft ABCD is shown in Figure 3 with total length, L = 2.1 m. The shaft BC is hollow with inner…

Q: Prob. # 3] The torsional deformation of a steel shaft is 1° in a length of 2 ft when the shearing…

A: Given data, L= 2ft= 24in. θ= 1°= 0.0174533 rad S= 10000 psi G= 12*10⁶ psi

Q: 3. From the figure shown below, determine the stress of member AB and BC. And calculate the maximum…

A: Given, G = 82.5 GPa = 82500 N/mm2dAB = 60 mmlAB = 1.2 m = 1200 mmdBC = 50 mmlBC = 0.8 m = 800 mm…

Q: A 55-mm-diameter solid circular shaft as shown in the figure is made up of an aluminum material. The…

Q: uter diameter 60 mm and inner diameter 40 mm) is running at 43 Hz. If the shaft transmits 156 kW,…

Q: A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in…

Q: b a A steel shaft of solid elliptical cross section has a semi-major axis of length, a, and a…

A: Given , length of the major axis , a =25 mm Length of the minor axis , b =13 mm Torque , T=550…

Q: A solid round aluminum shaft has a maximum allowable shear stress of 80 MPa. The shaft is 10 cm in…

A: Given Diameter, d = 10 cm Length, L = 1 m G = 28 MPa Shear stress = 80 MPa…

Q: 3. Does the distance from the cross section neutral-axis effects the calculated shear stress? How?…

A: Given questions : Does the distance from the cross section neutral axis effects the calculated shear…

Q: A solid shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

Q: A stepped shaft ACB having solid circular cross sections with two different diameters is held…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The 6061-T6 aluminum shaft shown in Figure has a cross-sectional area in the shape of an equilateral triangle. Determine the largest torque T that can be applied to the end of the shaft if the allowable shear stress is tallow= 8 ksi and the angle of twist at its end is restricted to fallow = 0.02 rad. How much torque can be applied to a shaft of circular cross section made from the same amount of material?
A solid steel shaft must not twist through more than 30 in a 6-m length whensubjected to a torque of 12 kN • m. (a) Find the diameter of the smallest shaft that can be used. (b) What is the maximum shear stress in the shaft of this diameter? Use G = 83 GPa for steel
A hallow steel shaft 2540 mm long must transmit torque of 34 KN-m. The total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 MPa. Find the inside diameter and the outside diameter of the shaft that meets these conditions. Use G = 83 GPa
complete solution A solid steel shaft must not twist through more than 30 in a 6-m length whented to a torque of 12 kN • m. (a) Find the diameter of the smallest shaft thatcan be used. (b) What is the maximum shear stress in the shaft of this diameter? UseG = 83 GPa for steel.
Design the size of solid steel shaft to be used for a 500 hp, 250rpm application if the allowable torsional deflection is 1o andthe allowable stress is 10,000 psi and modulus of rigidity is 13x 106 psi. Round your answer to the nearest 1/8 inch.
A shaft ABCD is shown in Figure 3 with total length, L = 2.1 m. The shaft BC is hollowwith inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and CDare solid with diameter d. Given the torque at A, B, C and D is 6 kNm, 14 kNm, 26 kNmand 6 kNm, respectively.a) Determine the maximum and minimum shearing stress in shaft BC. b) Calculate the required diameter, d of shafts AB and CD if the allowable shearingstress in these shafts is 65 MPa.
The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The shaft is to be designed to safely transmit 200 hp at 3500 rev/ min. Determine the diameter of the smallest shaft that can be used and its corresponding angle of twist. For the steel, use a working shear stress of 12 000 psi and G = 12 x 106 psifind, a) diameter b) angle of twist
A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further subjected to a torque of 10 kN-m. The maximum principal stress is ?
PLEASE ANSWER ASAP TY! The shaft shown has a diameter of 30 mm and is fixed at points A and B. Shear Modulus = 75 GPa. a) What is the internal torque in segment AC (in N-m)? b) Determine the maximum torsional shear stress experienced at segment AC (in MPa). c) What is the torsional shear stress at the center of the cross-section of the shaft (in MPa)? d) Determine the reactive torque at point B (in N-m).
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?