a) An alumium shaft shown in figure-2, has x-sectional area in the shape of equilateral triangle. if Tallow = 56 MPa, Øallow = 0.02 rad, Ga = 26 GPa, Determine I. Determine largest torque T that can be applied to end of shaft. II. How much torque can be applied to a shaft of circular x-section made from same amount of material?

a) An alumium shaft shown in figure-2, has x-sectional area in the shape of equilateral triangle. if Tallow = 56 MPa, Øallow = 0.02 rad, Ga = 26 GPa, Determine I. Determine largest torque T that can be applied to end of shaft. II. How much torque can be applied to a shaft of circular x-section made from same amount of material?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
An alumium shaft shown in figure-2, has x-sectional area in the shape of equilateraltriangle. if tallow = 56 MPa, Pallow = 0.02 rad, Ga= 26 GPa, Determine Determine largest torque T that can be applied to end of shaft. And How much torque can be applied to a shaft of circular x-section made from same amount of material?
The 6061-T6 aluminum shaft shown in Figure has a cross-sectional area in the shape of an equilateral triangle. Determine the largest torque T that can be applied to the end of the shaft if the allowable shear stress is tallow= 8 ksi and the angle of twist at its end is restricted to fallow = 0.02 rad. How much torque can be applied to a shaft of circular cross section made from the same amount of material?
A steel shaft ABCD of length L=6.5 is shown in Figure 4. Given the torque at A,B,C and D is 80 kNm, 150 kNm, 60 kNm and 10 kNm, respectively. The shaft has a diameter of 200mm. Use G=79.3 GPa a) Determine the angle of twist of the end A. b) Calculate the angle of twist of A relative to C. c) Plot a diagram of torque, T versus length, L of the shaft.
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
A steel shaft ABCD of length L = 6.5 is shown in Figure 4. Given the torque at A, B, C andD is 80 kNm, 150 kNm, 60 kNm and 10 kNm, respectively. The shaft has a diameter of200 mm.a) Determine the angle of twist of the end A. b) Calculate the angle of twist of A relative to C. c) Plot a diagram of torque, T versus length, L of the shaft.
A shaft ABCD is shown in Figure 3 with total length, L = 2.1 m. The shaft BC is hollowwith inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and CDare solid with diameter d. Given the torque at A, B, C and D is 6 kNm, 14 kNm, 26 kNmand 6 kNm, respectively.a) Determine the maximum and minimum shearing stress in shaft BC. b) Calculate the required diameter, d of shafts AB and CD if the allowable shearingstress in these shafts is 65 MPa.
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?