A horizontal straight pipe gradually reduces in diameter from 300 mm to 150 mm. If, at thelarger end, the gage pressure is 275 kpa and the velocity is 3 m/s,what is the total longitudinalthrust exerted on the pipe? Neglect friction. Note the larger end is at point 1.RxPIP2-2150 mmø300 mmø

The total longitudinal thrust exerted on the pipe is a result of the following: Force due to change…

Answered: A horizontal straight pipe gradually…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A trapezoidal channel has a bottom width of 6 m and side slopes of 2H:1V. If thedepth of flow is 1.2 m and the flow is 20.40 m3/s,a. Compute the specific energy b. Compute the slope of channel if n = 0.014 c. Compute the average shearing stress at the boundary
Water flows through the 2-in-diameter pipe at 0.2 ??^3/s as shown in Fig. 5-19a. If the pressure at A is 30 psi, determine the pressure at C, and draw the energy and hydraulic grade lines from A to B. Neglect friction losses and take ?? = 62.4 ??/ft^3
The pressures at the ends of 605m long horizontal pipe flow are 350 kPa and 270 kPa. The pressure at the point between the ends is 300 kPa. The pipe is 305mm in diameter and n=0.018. Find the total headloss, amount of flow, and the slope of the egl.
Q7) A flow of 2 cumecs in a channel 2m wide has a uniform depth of 1m. Find the change in water surface elevation due to a contraction in width to 1.25m, and a smooth downward step in the bed of 50mm.
A rectangular channel 1 m wide, Chézy C = 60, S = 0.0064, carries 1 m/s. Determine the velocity.
1. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.) 39.5136 b.) 12. 9517 c.) 99.9358 d.) 30. 4889 2. What gage pressure p1 in kPa, is needed to provide the given flow rate? a.) 1121kPa b.) 1328kPa c.) 1692kPa d.) 1725kPa
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
Design a straight trapezoidal erodible channel that can carry a discharge of 12.5m^3/s using tractive force method based on the following information. The side slope is 1V:4H The bottom slope is 0.0015 The manning's roughness coefficient is 0.024 The critical shear stress as 7.2KN/m^2 Angle of repose is 23 Density of water 1000kg/m^3
Consider the simple pipe network below. Pipe AB and CF are both 500m long withdiameters of 0.8m and friction factors of 0.015. Branch 1 is 200m long, 0.5m in diameter with a frictionfactor of 0.02. Branch 2 is 300m long, 0.6m in diameter with a friction factor of 0.012. The designdischarge through pipe AB is 3m 3 /s. Determine the following: a) the equivalent pipe length, Leq, of asingle equivalent pipe with a diameter of 1m and friction factor of 0.02, that represents the entire pipenetwork from A to F, b) determine the total head loss from A to F. Ignore minor losses. (Hint: need touse method of equivalent pipes for both series and parallel)
A masonry dam having a sheet piling cutoff at the upstream and is located at a reservoir site as shown in the figure. Nf= 4; Nd= 10 and K= 0.003m/min 1) compute the seepage discharge in cu MTR/day 2) compute the uplift force acting on the base; 3) compute the exit or escape gradient of the water at the downstream tip of the dam if the length of the flow field is equal to 1.80m
Consider the steady open channel flow of water in the smooth constriction shown in plan view in Figure P10.46. At position 1, the depth is Y1, the width is B1 and the Froude number F1 = 4. A similar notation is used at positions 2, 3 and 4. A hydraulic jump is observed just downstream of position 2 where the Froude number F2 = 2. You may assume one-dimensional flow. (a) Find Y2, the depth at position 2, in terms of Y1. (b) Find Y3, the depth just downstream of the hydraulic jump, in terms of Y1. (c) Find F3, the Froude number just downstream of the hydraulic jump. (d) Find F4, the Froude number at the exit, given that Y3/Y4 = 1.2. (e) Find B4/B1.
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A horizontal straight pipe gradually reduces in diameter from 300 mm to 150 mm. If, at the larger end, the gage pressure is 275 kpa and the velocity is 3 m/s,what is the total longitudinal thrust exerted on the pipe? Neglect friction. Note the larger end is at point 1. Rx PI P2 F2 150 mmø 300 mmø