O A pipe 5 m long is inclined at an angle of 15° with the horizontal. The smaller section of thepipe, which is at a lower level is of 80 mm diameter and the larger section of the pipe is of240 mm diameter as shown in Figure 5.5 m240 mm80 mm 15°Datum lineFigure 5Determine the difference of pressure between the two sections, if the pipe is uniformlytapering, the velocity of water at the smaller section is 1 m/s and ywater is 9.81 kN/m³.

Answered: Image /qna-images/answer/4276be6f-eb30-40f3-aa29-95a015c01975.jpg

A pipe 5 m long is inclined at an angle of 15° with the horizontal. The smaller section of the pipe, which is at a lower level is of 80 mm diameter and the larger section of the pipe is of 240 mm diameter as shown in Figure 5. .5 m 240 mm 80 mmt 15 Datum line Figure 5 Determine the difference of pressure between the two sections, if the pipe is uniformly tapering, the velocity of water at the smaller section is 1 m/s and ywater is 9.81 kN/m³.

A pipe 5 m long is inclined at an angle of 15° with the horizontal. The smaller section of the pipe, which is at a lower level is of 80 mm diameter and the larger section of the pipe is of 240 mm diameter as shown in Figure 5. .5 m 240 mm 80 mmt 15 Datum line Figure 5 Determine the difference of pressure between the two sections, if the pipe is uniformly tapering, the velocity of water at the smaller section is 1 m/s and ywater is 9.81 kN/m³.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using n= 0.019 Choices: A. 1210.47 B. 1012.74 C. 2101.74 D.112.47
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses.
A vertical pipe 3 ft in diameter and 30 ft long has a pressure head at the upper end of 22 ft. of water. When water flows through it with mean velocity of 15 fps, the friction loss is 6 ft. Find the pressure head in ft. at the lower end of the pipe when the flow is downward. a. 58.0 b. 46.0 c. 69.6 d. 89.6
given data : the slope of the dam 2v/1h so the height of the dam 12 m/ the all width of the dam will be 6 m (the width of the rectangular part is b-6)/ the depth of the dam 60m coefficient of sheer resistance = 0.75 gamma concrete 24 KN/m2 tailwater level of water converted into the channel directly behind the dam is 0.5 m (you will see that detail right of the picture drawn) the strip is 1 m (a force acting from water to dam ) height of the dam 12m height of water in the dam 10 m questions? 1- calculate all force in the picture W1/W2/u(uplift force)/Fh1/Fh2?(horizontal and vertical forces must all be calculated ) 2-Determine the dam weight needed to achieve a sliding factor of safety of 1.5 3-Determine the moments imposed at the dam toe. 4-Determine the dam weight needed to achieve an overturning factor of safety of 2. 5-Assuming that the dam downstream is with a slope of 1V/2H determine the dam base width to satisfy the stability requirements? 6-At the dam bottom an emergency…
Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .b) The discharge through the venturi section
A jet is issued from the side of a tank under a constant head asshown in the figure. The side of the tank has an inclination of 1H:1V.The total depth of water in the tank is h1 = 6.7m and the orifice islocated at h2 = 3.7m above the bottom of the tank. The the horizontalfloor surface is at h3 = 1.2m below the bottom of the tank. If Cv = 1.0and neglecting air resistance, then Determine the maximum height (y) to which the jet will rise abovethe orifice.
In the branched pipe system below, water is flowing at 0.0142 m3/sin a new, clean DN 100 Schedule 40 pipe (ID = 0.1023 m) at A. The flow splits into two new, clean DN 50 Schedule 40 pipes (ID = 0.0525 m; A = 0.00216 m2) as shown and then rejoins at B. Call the 30 m branch“a” and the other branch “b.” The friction factor in Branch ais 0.021, and the friction factor in Branch bis 0.0215.(Note that if friction factors weren’t given, you’d need to make initial guesses and iterate!)Calculate the flow rate in each of the branches. Include the effect of all minor losses in Branch bbut ignore the tee junctions. The total length of the pipe inBranch bis 60 m. The elbows are standard.(Remember to check that your final answers follow continuity!)
Hydraulic structure Q.2: Given the following data of a head regulator: The discharge= 60 cumecs, bed level of the canal-52.2m, crest level of the regulator=52.8m, upstream water level-54.2m, downstream water level=53.9m. The dimension of gates= (2.5x3)m and the thickness of the piers is 0.9m. Neglect the velocity head and use coefficients of discharge= 0.8 and 0.577. Determine the water way of the regulator
water from a reservoir flows at 0.85 m3/s through a rigid pipe 1200 mm diameter and completely stopped by a closure of a valve almost instantly. Bulk modulus of water is 2.20 x 109 N/m2. a) Find the water hammer pressure for sudden closure. b) Find the discharge if water hammer pressure is 700 KPa. c) If the time of closure of valve is 4 sec. and located at 650 mm from the reservoir, find the water hammer pressure at flow rate at 0.85 m3/s.
A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C inclined at 45 degrees. Find the maximum height and range that the water can reach if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m.