Answered: Determine the stress developed in the…

Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches and the bar weigh 6kips.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.5.16P: A rubber sheet in biaxial stress is subjected to tensile stresses ax= 270 Pa ander,. = 144 Pa. The...

See similar textbooks

Related questions

Q: Determine the largest intensity w of the distributed load that the member can support if the…

A: The free-body diagram of the beam can be drawn as follows, The reactions at A and B respectively…

Q: Determine the average normal stress in rod AB if the load has a mass of 50 kg. The diameter of rod…

A: Given figure mass of the load = 50 Kg Weight of the load

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The…

A: Given that: diameter of rod 1 = 15 mm diameter of rod 2 = 28 mm It is required to determine the…

Q: During the tension test, the wooden specimen is subjected to an axial force (P = 4 kip) applied to…

A: Given data Force (P) = 4 kip

Q: 7. Determine the stress developed in the Tensional Cord given that the cable’s diameter is 0.6…

A: Given, Weight of the bar = W = 6 kips Diameter of cable = d = 0.6 in AB = 5 m BD = 3 m BC = 5 m…

Q: Determine the torsional stress in the thin-walled tube as shown:

Q: If the allowable normal stress for the bar is s allow = 120 MPa, determine the maximum axial force P…

A: Write the given data:

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point B,…

A: d=1in Draw the free diagram of the problem by converting the eccentric loads into the loads and…

Q: The yoke-and-rod connection is subjected to a tensile force of 15 kN. Determine the average normal…

A: Given data: Applied force (F) = 15 kN G = 75 GPa Need to determine the average normal stress in each…

Q: Determine the maximum normal stress that loading produces in the steel member.

Q: The steel bracket is used to connect the ends of two cables. If the applied force P = 1.50 kip,…

A: Draw the free body diagram.

Q: Determine the stress in the cable BC if the mass of the cylinder is 250 kg. The cross sectional area…

Q: The plate welded to the end of the l-beam is fastened to the support with four 10-mm-diameter bolts…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The forces and torques at point B are shown as, On using equilibrium of forces in x, y, and…

Q: If the allowable tensile stress for wires AB and AC is sallow = 180 MPa, and wire AB has a diameter…

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

Q: The coupling is used to connect the tWo shafts together. Assuming that the shear stress in the bolts…

Q: The steel bracket is used to connect the ends of two cables. If the allowable normal stress for the…

A: Given data

Q: Determine the maximum axial force P that can be applied to the bar. The bar is made from steel and…

A: The given bar is critical to two positions:1) At the fillet section2) At the hole sectionAt fillet…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

Q: For the connection shown, the average shear stress in the 11-mm-diameter bolts must be limited to…

Q: Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension…

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: Introduction: The tension is created by fighting the bursting effect of the imposed internal…

Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A,…

A: Given data: Permissible screw stress,σtper=150MPa Permissible bearing stress for wood, σbper=28MPa

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the inner diameter…

A: Write the given data: Understand that the stress generated at point A will be the tangential stress…

Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ Required : Force

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: Determine the shear stresses experienced by the four identical circular bolts of diameter 20 mm used…

A: Given data: F = 150 kN d = 20 mm Need to determine the shear stress in each bolt.

Q: The strut is glued to the horizontal member at surface AB. If the strut has thickness of 25mm and…

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P =…

Q: Determine the average normal stress developed in rod AB if the load has a mass of 64 kg. The…

Q: The 1-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point A,…

Q: The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, respectively. Determine the…

Q: The two aluminum rods support the vertical force of P = 20 kN. Determine their required diameters if…

A: Given Data: The load at point A is P = 20 kN. The allowable tensile stress for aluminum is sallow=…

Q: Determine the average normal stress in each of the 20-mm-diameter bars of the truss. Set P = 40 kN.

A: Given Data P = 40KN diameter, d=20mm Area, A = πd24=π0.02024=3.14×10-4m2 tanθ=1.52 θ=36.86°

Q: a) In the composite spring shown, Spring 1 has a mean coil diameter of 36 mm and a wire diameter of…

Q: Q5: Determine the average normal stress developed in rod AB if the load has a mass of 50 kg. The…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Q1: The 20-kg chandelier is suspended from the wall and ceiling using rods AB and BC, which have…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium when the sum of the forces…

Q: The bars of the truss each has a cross-sectional area of 780 mm?. Determine the average normal…

Q: If the block is subjected to a centrally applied force of P = 6 kip, determine the average normal…

A: The area of the cross-sectional = 14(6)-2(1)(4)=76 in2 σavg=PAσavg=676=0.0789 ksiσavg=PA=78.95 psi

Q: If P 4 kN, determine the stress in the inner spring and the displacem of the plate. The inner spring…

Q: The 0.97 in diameter rod is subjected to the loads shown. Determine the normal and shear stress at…

A: To find: The normal and shear stress at point B. Given: The diameter of the rod is d=0.97 in.…

Q: Determine the maximum distance d to the edge of the plate at which the force P can be applied so…

A: Given, Load=P Distance of the load from the bottom=d Thickness of the plate= 200mm Solution Tensile…

Q: Determine the normal stress o (MPa).

A: Given: σx=67.3 MPaσy=25.5 MPaτxy=-24.3 MPaα=48.3°To determine:Normal stress σt

Q: Q3/ During the tension test, the wooden specimen is subjected to an average normal stress of 5 ksi.…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

7. Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6
inches and the bar weigh 6kips.
Figure P-106
3 m
5 m
5 m
E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A rubber sheet in biaxial stress is subjected to tensile stresses ax= 270 Pa ander,. = 144 Pa. The corresponding strains in the sheet are e. = 0.0002 and = 0.000015. Determine Poisson’s ratio and the modulus elasticity of the material.
Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.