theQUESTION 2: (30 points) For the shaft in below, motor gives a 500 Nm torque on the shaft when it is rotation with aconstant speed. Torques of two pulleys are known as shown in the figure. If the shaft is made of A-36 steel alloy,determine the maximum shear stress that is generated through the shaft.300 N - m200 N m48 mm0.9 m44 mm1.2 m40 mm1m

d1= 40 mm L1=1 m d2=44 mm L2=1.2 m d3=45 mm L3=.9 m

Answered: determine the maximum shear stress that…

determine the maximum shear stress that is generated through the shaft. 300 N - m 200 N- m 48 mm 0.9 m 44 mm 1.2 m 40 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Related questions

Q: F10-6. Determine the shear stress at point A on the surface of the shaft. Represent the state of…

A: Given Data: Radius of the shaft is r = 40 mm. Distance of point A from the free end of the shaft =…

Q: Determine the maximum s hear stress developed in the beam. 20 KN/m 0.25 cm 1.5 cm 2 cm 3 KN 0.25 cm…

A: A beam is said to be a over-hanging beam if the the ends of the beam is extending beyond supports it…

Q: Treat A as a support wall and determine the Maximum shear stress in the shaft and the rotation of C,…

A: Diameter of steel shaft d=40 mm LAC=300 mm ,LCD=400 mm ,LDB=500 mmG=75…

Q: 6kN and 1.0kNm loads are applied to the top of the 62-mm-diameter cast-iron as shown. Determine the…

Q: The two steel members are joined together using a 30° scarf weld. Determine the average normal and…

A: Separating both the portions of the steel members and showing the forces on the plane a-a

Q: Determine maximum shear stress Maximum principal stress-44 MPa Minimum principal stress=38 Mpa

A: Given data : Maximum principal stress σ1=44 MPa Minimum principal stress σ2=38 MPa Required :…

Q: Solve Prob. for the normal stress acting perpendicular to the seam.

A: Given data: Normal force, F = 200 N From the diagram it is clear that it is uniaxial state of…

Q: Determine the maximum shear stress in the 40-mm-diameter shaft.

A: The torque on the pulley B is The torque on the pullet A is The maximum torque in the shaft is

Q: Determine the maximum shear (k) at the given structure. 10 k 0.8 k/ft 8 k |C B. ton -6 ft -12 ft- 12…

A: Given data: w=0.8 k/ft Need to determine the value of maximum shear force.

Q: Qi: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr Tmax Ip Ex

Q: Axial force of 900 N and torque of 2.50 N-m are applied to shaft. If shaft has a diameter of 40 mm,…

Q: FI0-5. Determine the maximum shear stress in the shaft at section a-a. G00 N-m -30 mm 1500 N-m 40 mm…

A: The outer radius of the section a-a of the shaft is given as R = 0.04 m. The inner radius of the…

Q: etermine the absolute maximum shear stress.

A: Given that , σxx=-79.7 MPaσyy=50.5 MPaτxy=-24.9 MPa

Q: 10 kip 5 kip 3 kip

A: GIVEN DATA Double shear connection 10 kip force at middle plate 5 kip forces on upper and lower…

Q: Determine maximum shear stress

A: Given data: σx=100 MPaσy=20 MPaτxy=40 MPa Need to determine the maximum shear stress.

Q: Q2:The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in…

Q: Part A a. Take T = 650 N. m and T, = 1565 N. m. Determine the maximum shear stress developed in the…

Q: Determine the shear stress at point H. V= 80 kN. H Q 80 [mm] 12

Q: Determine the average punching shear stress the circular shaft creates in the metal plate through…

A: Given data: The value of shear load is F=40 kN The diameter of shaft is dAB=50 mm The thickness of…

Q: Determine the largest shear force V that the member can sustain if the allowable shear stress is…

Q: F1-11. Determine the average normal stress developed at points A, B, and C. The diameter of each…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Determine the maximum shear stress developed in the shaft at section a - a. Take T = 700 N. m and T…

A: Given data: T1=700 N.mT2=1555 N.m Need to determine the maximum shear stress at a-a section.

Q: Determine maximum shear stress Maximum principal stress=25 MPa Minimum principal stress=-5 MPa

A: Maximum principal stress, σmax=25 M PaMinimum principal stress, σmin=-5 MPa

Q: 2. The shaft is hollow from A to B and solid from B to C. (a) Determine the maximum shear stress…

Q: The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial…

A: Given: The cross-sectional area of the bar, A = 400x10-6 m2 Force equilibrium in x-direction, The…

Q: A torque of 2 kip # in. is applied to the tube. If the wall thickness is 0.1 in., determine the…

A: Torque T = 2 kip in = 0.16 kip ft thickness t = 0.1 in rm = (2 + 1.9)/2 in =1.95 in Am = π4 rm2=…

Q: The shaft is used to transmit 30 hp while turning at 600 rpm. Determine the maximum shear stress in…

A: The value of power transmitted is 30 hp. Convert the power from hp to Watt by multiplying with 746.…

Q: В The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. If the…

Q: Determine the shear stress at point A on the surface of the shaft. Represent the state of stress on…

A: Write the twisting moment at the cross section containing point A.

Q: Determine the average punching shear stress the 40 kN circular shaft creates in the metal plate…

Q: F1-11. Determine the average normal stress developed at points A, B, and C. The diameter of each…

Q: Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated…

A: Given data: The diameter of the segment at A, dA = 0.5 in. The diameter of the segment at B, dB = 1…

Q: Determine the maximum shear force V that the strut can support if the allowable shear stress for the…

A: Given data: allowable shear stress (τallow) = 40 MPa =τmax Find, Maximum shear force (Vmax)

Q: etermine the maximum shear stress in

Q: Determine the stresses at point A. The circular solid shaft has a radius of 40 mm. 300 тm 200 mm B.…

A: Given Data, F= Eccentric shear force = 30 KN r= Radius of the shaft = 40mm According to the diagram…

Q: Question 1: E The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear…

Q: maximum shear stress

Q: Determine the maximum shear stress in the shaft at section a -a.

A: Calculate the maximum torque from point A. T=1500 N·m+600 N·m=2100 N·m Write the shear stress…

Q: 90 100 mm 100 mm- 10. The average shear stress in each of the 6-mm radius bolts and along each of…

Q: 2. Draw Mohr's circle that describes each of the following states of stress. 5 MPa (a) 5 MPa (c) 20…

A: (a) To draw: The Mohr's circle. Given: The state of stress is shown below.

Q: Determine the maximum average shear stress developed in each 3>4@in.-diameter bolt.

A: Given Data Diameter d=3/4 in Area =πd24=π4342=0.4415in2

Q: Determine the largest shear force V that the member can sustain if the allowable shear stress is…

A: Determine the y coordinate of the cross section of the given area with respect to the considered…

Q: Determine the shear stress (in Mpa) in the 27.99-mm-diameter pin at A that support the beam if P =…

Q: The shaft is subjected to a maximum shear strain of 0.0048 rad. Determine the torque applied to the…

A: Given Data The maximum shear strain is: γmax=0.0048 The minimum shear strain is: γmin=0.0006 The…

Q: A pressure vessel containing gas at 250 psi has an outer diameter of 12 inches and a thickness of…

Q: The bar has a circular cross section with 1-in diameter. If the torque TO = 1000 in-lb, determine…

Q: s constructed from three boards bolted together as shown in Fig. Determine the m shear stress if the…

A: Given data: Shear Force V=35 kN Spacing between each of the bolt is s=250 mm

Q: F144. Determine the equivalent state of stress on an clement at the same point that represents the…

A: σx=100 kPaσy=700 kPaτxy=-400 kPa

Q: The built-up shaft is designed to rotate at 450 rpm. If the radius of the fillet weld connecting the…

A: givenrpm N=450rpmthe radius of the fillet weld connecting the shafts is r = 13.2 mmthe allowable…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).