A jet impinges on a splitter block. The incoming jet is horizontal and has a flow rate of Q1 = 8000 cm³/s and a cross-sectional area of A, = 40 cm?. The block splits the jet in to two smaller jets. One is deflected upward by 45°, and has a flow rate of Q2 6000 cm/s and a cross-sectional area of A, = 30 cm2. Thebther jet is deflected downward by 45°, and has a flow rate of Q3 = 2000 cm³/s and a cross-sectional area of A3 = 10 cm2. You may assume that the pressure everywhere is equal to atmospheric pressure, and the density of the fluid is 1000 kg/m3. Find the horizontal momentum flux in, in

A jet impinges on a splitter block. The incoming jet is horizontal and has a flow rate of Q1 = 8000 cm³/s and a cross-sectional area of A, = 40 cm?. The block splits the jet in to two smaller jets. One is deflected upward by 45°, and has a flow rate of Q2 6000 cm/s and a cross-sectional area of A, = 30 cm2. Thebther jet is deflected downward by 45°, and has a flow rate of Q3 = 2000 cm³/s and a cross-sectional area of A3 = 10 cm2. You may assume that the pressure everywhere is equal to atmospheric pressure, and the density of the fluid is 1000 kg/m3. Find the horizontal momentum flux in, in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 30° elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward The elbow discharges water into the atmosphere Cross-sectional areas of the elbow are 113 cm^2 at the inlet and 7 cm^2 at the outlet. The elevation difference between the centers of the outlet and the inlet is 30 cm Neglect the weight of the elbow and the water inside the elbow,Using appropriate integral equations, find a) Wet and outset velocity b) Gage pressure at the center of the inlet section of the elbow c) Anchoring force required to hold the elbow In place Take the density of water to be 1000kg/m^3 & the flow is incompressible.
Water is flowing horizontally in a pipe that has a diameter of 25cm. The water is flowing at 8 m/s. At 300 kPa gage the water enters a 90 degree bend reducing section, which is connected to a vertical pipe that has a diameter of 15cm. The inlet of the bend is 45 cm above the exit. If friction and gravity are negligible and the momentum flux correction factor is 1.04, how would I determine the net resultant force exerted on the reducer by the water?
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
A projectile-like object with maximum diameter of 20 cm is placed at the exit of a 25-cm-diameterpipe. Water flows through the pipe. At the upstream location 1, the velocity is uniform and equalto 2 m/s. The water exits to the atmosphere where the pressure is 100 kPa. Find the force requiredto hold the object in place. Be sure to state your assumptions.
A reducing elbow in a horizontal pipe is used todeflect water flow by an angle ϴ = 450from the flowdirection while accelerating it (Fig. 3). The elbowdischarges water into the atmosphere at a rate of 30kg/s. The cross-sectional area of the elbow is 150cm2 at the inlet and 25 cm2 at the exit. The elevationdifference between the centers of the exit and theinlet is 40 cm. The mass of the elbow and the waterin it is 50 kg. Determine the anchoring force neededto hold the elbow in place. Take the momentum-fluxcorrection factor to be 1.03 at both the inlet andoutlet. Density of water ρ = 1000 kg/m3, atmosphericpressure 101.0 kPa and g = 9.81 m/s2. Assumesteady, incompressible, frictionless and irrotationalflow.
Water flows through a pipe of 0.0025 m^2size with a uniform velocity of 7m/s and flows out from an ariface at bottom at a rate 0.003 m^3/s. what is rate of change of mass of water in the tank?
Water falls vertically downward from an open faucet with an initial velocity of 66 cm/s. If the stream diameter at the faucet head is 0.5 cm what is the stream diameter at a distance 5 cm below the faucet exit?
A converging elbow tirms water to a nozzle in a vertical plane, The elbow cross section diameter is (20 cm) at the inlet, and (10 cm) at the outlet. The water volume flow rate is (200 L/s) and the elbow inlet pressure is unknown but it discharge the water 1o the atmosphere (101.325 kpa). Calculate the horizontal and vertical force required to old the elbow in place. (neglect the weight of elbow and water).
Water exits a 1-cm diameter outlet of a faucet. Estimate the maximum speed that would result in a laminar flow if the water temperature is 50°C. Assume Re = 2000 a. 558 m b 6.15 m c7.71 m d 845 m
To avoid the bulky tower and impeller and generator inthe HAWT of the chapter-opener photo, we could insteadbuild a number of Darrieus turbines of height 4 m anddiameter 3 m. (a) How many of these would we need tomatch the HAWT’s 100 kW output for 15 m/s wind speedand maximum power? (b) How fast would they rotate?Assume the area swept out by a Darrieus turbine is twothirdsthe height times the diameter.
Suppose that there is a 4-cm water jet with a velocity of 15 m/s which hits a vertical plate with a mass on 800 kg. This plate is mounted on a track which is nearly frictionless and starts out not moving. when the jet strikes the plate, water leaves by splashing out in the plane of the plate. what is the acceleration of the plate when the jet first hits it? What is the velocity of the plate after 60 seconds? Assume that the momentum correction factor s 1.04.