A joint is made by gluing two plywood gussets of thicknesst to wood boards. The tensile working stresses are 1300 psi for the plywood and 800 psi for the boards. The working shear stress for the glue is 55 psi. a. Determine the dimension b (inch.) so that the joint is as strong as the boards. c. 11.67 1.75 in. а. 38.33 b. 12.73 d. 40.25 -b- b. Determine the dimension t (inch.) so that the joint is as strong as the boards. a. 0.477 b. 1.36 P P c. 0.538 5.75 in. d. 0.562

A joint is made by gluing two plywood gussets of thicknesst to wood boards. The tensile working stresses are 1300 psi for the plywood and 800 psi for the boards. The working shear stress for the glue is 55 psi. a. Determine the dimension b (inch.) so that the joint is as strong as the boards. c. 11.67 1.75 in. а. 38.33 b. 12.73 d. 40.25 -b- b. Determine the dimension t (inch.) so that the joint is as strong as the boards. a. 0.477 b. 1.36 P P c. 0.538 5.75 in. d. 0.562

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 75-lb block has a downward velocity of 2 ft/s when it is 3 ft from the top of the beam. Determine the maximum bending stress in the beam due to the impact, and calculate the maximum deflection of point B. Ew = 1.9(103) ksi.
l = 20'0" w = 2 kips / ft Beam: W21 x 50 FIND: - Maximum Shear - Maximum Moment - Maximum Deflection -The stress due to bending and shear stress in the web.
g. What is the moment of inertia (I) about the neutral axis of the section? (in mm^4) h. What is the first moment of an area (Q) about the neutral axis of the section? (in mm^3) i. What is the maximum shearing stress (fv) of the beam? (in MPa) j. What is the maximum flexural stress (fb) of the beam? (in MPa)
A 110-N force acting in a vertical plane parallel to the yz Plane is applied to the 220-mm-long horizontal handle AB of a socket wrench. Determine the point O moment of that force.
A compressed bar having a square cross section of width b must support a load P = 37kN. The two parts of the bar are connected by a glued joint along plane p - q, which is at an angle = 40degree to the vertical. The allowable stresses in the glued joint are 5.3 MPa in compression and 3.4 MPa in shear. Considering only the glued joint, determine the minimum width b of the bar. choices are: 73. 202 54. 221 67. 054 59. 192 84. 353 104. 320
The magnitude if the bending moment acting o the circular cross-section of a beam is M=30 000 lb-ft. A. Calculate the bending stress at point A. Choices: 9.07ksi,7.68ksi,10.48ksi,11.36ksi, B.Calculate the bending stress at point B Choices: 9.07ksi,7.68ksi,10.48ksi,11.36ksi C.Calculate the bending stress at point C Choices: 9.07ksi,7.68ksi,10.48ksi,11.36ksi
A simply supported beam has a concentrated load at midspan. If the beam properties are given below, what is the final stress at bottom of the beam section where the maximum moment is located and the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 289 mmBeam height = 498 mmConcentrated load = 22.79 kNSpan of the beam = 9 mPrestressing force = 385 kNeccentricity = 123 mm
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa
Proposed exercise N ° 01 Find the angle of torsion of the free end with respect to the fixed end of the system in the figure. The material is steel and the dimensions are in cm. Proposed exercise N ° 2 Find the length that a hollow steel bar of D = 1.5cm and d = 0.5cm in diameters must have for its ends to rotate 30 ° relative to each other. An allowable shear stress of 713.8 kg / cm2 must not be exceeded, and G = 8.1573x105 kg / cm2
The plate is subjected to the two forces at A and B asshown. If θ = 60°, determine the magnitude of the resultantof these two forces and its direction measured clockwisefrom the horizontal.
A film of oil exists between two horizontal plates spaced 3mm apart. The lower plate is fixed and theupper plate is pulled with a constant velocity. The velocity profile between the two plates is found to have a nonlinear profile that is defined as u = (9y – 0.6y2) mm/s where y is in mm. Assuming the top plate has an area of 0.5 m2and the viscosity of the oil is μ = 0.437 N·s/m2, determine (a) the shear stress 1mm above the fixed plate, and (b)the force required to pull the upper plate
the largest axial P force that the given riveted joint can safely carry.calculate. Rivet diameter 28mm and plate width 340mm. Shear stress of the rivet1400 kg/cm2, crush safety stress of rivet 2800 kg/cm2and the platetensile safety tension 1400 kg/cm2will be taken. t1=21mm t2=38mm