A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15800 ksi] rods, and a solid steel [E = 27600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.62 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.41 in. Assume L₁=30 in and L₂-62 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P=32 kips is applied. Answers: 0₁ = 0₂ = 1 1 ܕܐ (2) B ksi. ksi. 4₁

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15800 ksi] rods, and a solid steel [E = 27600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.62 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.41 in. Assume L₁=30 in and L₂-62 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P=32 kips is applied. Answers: 0₁ = 0₂ = 1 1 ܕܐ (2) B ksi. ksi. 4₁

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two helical springs A and B with ground ends are made of the same material and are in parallel. The wire diameter of the springs A and B are 11 mm and 8 mm, respectively, and the spring indices of A and B, are 6 and 10, respectively. Determine the load supported by spring A in N if the load supported by spring B is 490 N.
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB.
Part A - Force with a known deflection The square bar shown (Figure 1) is 2.7 in.in. thick and 13 ftft long and is fixed supported at both ends. A load directed leftward is applied at point C, as shown, L2 = 11 ftft from the left end. The modulus of elasticity is E = 1.5×104 ksi .If point C moves δ= 6×10−3 in.in. to the left, what is the applied force? Part b Consider a new structure, where the thickness of the bar is reduced to 1.35 in.in. from C� to B� (it is still square) (Figure 2) and x=11ft. If the applied load is F� = 115 kipkip , then what is the reaction at A�? Let a positive reaction act to the right. The total length is still 13 ftft .
A mass of 1019Kg is supported by two wires A and B each made of a different material. Before loading the wires are of equal length. After loading they are still of equal length. Find the load carried by each wire. Wire Diameter mm E Nmm-2 A 1 206,000 B 2 116,000
A 2.25 m long solid bar (Lo) with a 32 mm diameter is placed under tension by a load (F) of 250 kN. The bar is solid and made of a homogeneous material with a Young’s Modulus E = 250 GPa. Calculate the extension of the bar (△L). Give your answer in millimeters (mm) to two decimal places.
A cylindrical rod of steel (E = 207 GPa) having a yield strength of 45,000 psi is to be subjected to a load of 11,100 N. If the length of the rod is 20.0 in., what must be the diameter to allow an elongation of 0.38 mm?
(a)Describe, with a labelled diagram, how you would measure accurately theextension of such a wire under an applied load. (b) The graph below shows how the extension of a wire varies with the loadapplied to it. The wire used has a length of 3m and a diameter of 5 x 10^-4m i. Calculate the tensile stress produced by a load of 50N.ii. Find the energy stored in the wire when the load is acting.iii. Calculate the reduction in gravitational PE of a 5kg mass used to providethe load.iv. Calculate Young's modulus for the metal of the wire.
A steel rod with a cross-sectional area of 180 mm2 is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 10-6 mm/ (mm°C) and E = 200 GPa. Which of the following most nearly gives the temperature at which the compressive stress will be 48 MPa? Which of the following most nearly gives the temperature at which the tensile stress will be 48 MPa? Which of the following most nearly gives the temperature at which the stress will be zero?
A) A circular rod with a gage length of 3.6 m and a diameter of 2.3 cm is subjected to an axial load of 51 kN . If the modulus of elasticity is 200 GPa , what is the change in length? B)A circular rod with a length of 4 m and a diameter of 2.4 cm is subjected to an axial load of 61 kN . If the resulting change in length is 3.34 mm , what is the modulus of elasticity? C)A circular rod with a length of 3.7 m and a diameter of 2.7 cm is subjected to an axial load and increases in length by 3.26 mm . The initial portion of the stress-strain curve of the material is given. What is the applied load?
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied parallel to the 2.3m dimension, what is the change in length of the rod?
A cord 10m long is hung between two posts 6m apart. What maximum load hung at the middle can the system support if the tensile strength of the cord is 350 N?
A steel rod with length equal to 12 ft, has a diameter of 0.8 inches in quarter of its length and a diameter of 0.4 inches the rest. If it is subjected to a tensile load of 6,500 lbs, what will be the total deformation of the bar if it has a modulus of elasticity E = 29.5 10^6 psi.