Hello Sir,Good Afternoon.I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice. Thank You A metal plate 1 m long, 1 m wide and 1 cm thick (k180.K,p = 2800 , Cpm3kg= 880-.K) haskgman initial temperature of 20°C. The metal plate is then heated in an oven at a constanttemperature of 800°C and convection coefficient of 200",.K for 2 minutes. How the finalm2temperature of metal plate ?

Answered: Image /qna-images/answer/d55c7c14-c449-4cbd-96a0-8e284c455dd5.jpg

A metal plate 1 m long, 1 m wide and 1 cm thick (k 180 kg .K,p = 2800 , Cp = 880. K) has an initial temperature of 20°C. The metal plate is then heated in an oven at a constant m m3 kg temperature of 800°C and convection coefficient of 200. K for 2 minutes. How the final W m2 temperature of metal plate ?

A metal plate 1 m long, 1 m wide and 1 cm thick (k 180 kg .K,p = 2800 , Cp = 880. K) has an initial temperature of 20°C. The metal plate is then heated in an oven at a constant m m3 kg temperature of 800°C and convection coefficient of 200. K for 2 minutes. How the final W m2 temperature of metal plate ?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.48P: The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of...

See similar textbooks

Similar questions

A 0.6-cm diameter mild steel rod at 38C is suddenly immersed in a liquid at 93C with hc=110W/m2K. Determine the time required for the rod to warm to 88C.
3.2 High-strength steel is required for use in building structures and equipment (e.g., cranes). It is produced by heat treating quench-hardened steel in a process called tempering that reduces brittleness and imparts toughness. In a production facility, alloy steel plates (k = 50 W/m K, c = 460 J/kg K, and ρ = 7865 kg/m3) of thickness 3.0 cm have to be tempered in a convective oven by heating them to 550°C. If the plates are initially at 40°C and the air inside the heat treating oven is at 700°C with a convective heat transfer coefficient of 45 W/m2 K, determine how long the plate has to remain in the oven.
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
A 12-by-12 inches ingot iron casting 60-in high is stripped from its moldwhile its temperature is 1740 °F. If it stands on end on the floor of a largefoundry having wall, floor, and roof temperatures of 80°F, what is the rate ofradiant-heat exchange between the casting and the roof wall, and floorsurfaces?
What is the minimum amount of ice at OPC that must be added to the contents of a can of diet cola (340m) to cool it down from 20.5C to 0C Assume that the specific heat and density of the diet colo are the same as for water and that no heat is gained or lost to the surroundings. The latent heat of fusion of ice à 3353/g Specific Heat of water 4.184 J/gK and Density of water is 1 g/mL
For a specified heat input and a given volume which material will have the smallest tempera- ture rise (Use data book if necessary) (a) steel (b) aluminium (c) water (d) copper. When a hot metal piece is left to cool in air the time rate of cooling of the outer layer will be (a) slower at start and faster near the end (b) faster at start and slower near the end (c) both rates will be the same (d) this will depend on the material. (viii) A thin black plate at temperature T receives radiation from a surface at Temperature T1 and radiates to a surface at T2. If all surfaces are black at steady state (a) (T1 – T) > (T – T2) (b) (T1 – T) < (T – T2) (c) (T1 – T) = (T – T2) (d) can be any one of a, b or c. (ix) The temperature profile (in) a slab initially at a constant temperature and then allowed to cool by convection for a short time will be as shown in Fig : (a) E1.2a (b) E1.2b (c) E1.2c (d) E1.2d. Ti
Example 3.3: The temperature at the center of a tender-boiled potato needs to be 98.9°C. Let's take a potato with 4 cm diameter at 5°C and and put it in vigorously boiling water at 100 °C, where convection coefficient is 1200 W/m². c. How much time will it take to cook the potato? Potato properties: density p=1070 kg/m³, conductivity k=0.8 W/m.°c, specific heat c = 3400 J/kg-°C.
ure f) A steel disc (k = 56.7 W/m.K, p = 7854 kg/m³, c = 487 J/kg. K) 30 cm in diameter and 10 cm thick, initially at uniform temperature of 265 °C is immersed in liquid at -15 °C. The convective coefficients on ends and on cylindrical side are 340 and 1420 W/m².K, respectively. What is the temperature at (a) center of disc, and (b) surface at centre of one end (c) Calculate heat transfer after 5 min have elapsed.
A small stainless-steel rod 7 mm in diameter was heated so it is at 300 °C. It is quenched in a bath of room temperature water, where it has a heat transfer coefficient of 30 W/m2K. How long will it take to be cool to the touch? Justify your answer and all assumptions. (You will generate a time constant and the Bi for this problem.
Steel balls 12 mm in diameter are annealed by heating to 1100 K and then slowly cooling to 360 K in an air environment for which T. = 325 Kand h = 20 W/m2-K. Assuming the properties of the steel to be k = 40 W/m-K,p = 7800 kg/m, and c = 600 J/kg-K, estimate the time required for the cooling process. The time required for the cooling process isi h.
A 30 mm diameter copper sphere and a 30 mm copper cube are both heated in a furnace to 923 K. They are then annealed in an air at 378K. If the external heat transfer coefficient h is 80 W/m2.K in both cases, what is the temperature of the sphere and of the cube at the end of 6 minutes