A meter of polyaramide fiber has a diameter of 560. μm, a mass of 0.143 g, and takes 0.43 s to produce on an industrial spinneret. How would you calculate the mass of fiber that can be spun in 20. min? Set the math up. But don't do any of it. Just leave your answer as a math expression. Also, be sure your answer includes all the correct unit symbols. mass of fiber = 0 0.0 ? 30 4 ola X O

A meter of polyaramide fiber has a diameter of 560. μm, a mass of 0.143 g, and takes 0.43 s to produce on an industrial spinneret. How would you calculate the mass of fiber that can be spun in 20. min? Set the math up. But don't do any of it. Just leave your answer as a math expression. Also, be sure your answer includes all the correct unit symbols. mass of fiber = 0 0.0 ? 30 4 ola X O

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section8.2: Rotational Dynamics

Problem 13PP

See similar textbooks

Similar questions

How many forces provide the counterclockwise torque in the first part of the experiment? P.s. I had this question answered but I was confused on what the actually answer is. Is there only one force or three forces providing the couterclockwise torque? Please clarify more.
An engineer estimates that under the most adverse expected weather conditions, the total force on the highway sign in the figure (Figure 1) will be F→=(±2.1i^−4.2j^)kN, acting at the cm. What is the magnitude of the torque this force exert about the base O? Express your answer using two significant figures.
Angular expression of a disk drive is given by θ(t) = a + bt + ct3 ,where a, b and c areconstants. t is in seconds and θ is given in radian. At the instant t = 0, θ = π/4 and angularvelocity is 2 rad/s . At t = 1.5 s, angular acceleration is 1.25 rad/s2 . According to thisinformation, (a) find constants a,b and c with corresponding units. (b) When angle is θ = π/4 ,what is the angular angular acceleration? (c) When angular acceleration is 3.5 rad/s2 what are the angle θ and angular velocity?
Luis uses a 20-cm-long wrench to tighten a nut, turning it clockwise. The wrench handle is tilted 30° above the horizontal, and Luis pulls straight down on the end with a force of 100 N. How much torque does Luis exert on the nut?
A Ferris wheel has radius of 5.0 m and makes one revolution in 8.0 seconds. A person weighing 670 N is sitting on one of the benches attached at the rim of the wheel. What is the apparent weight (that is, the normal force in Newtons exerted on her by the bench) of the person as she passes through the highest point of her motion? (Don't forget about sigfigs) I understand how to calculate the answer but cannot determine the correct number of sig figs for the final answer.
Now that you know how to calculate the torque using components of vector r, plug in values from a trial of your choice. The mass of the weights in each trial are: Trial 1: 4.54 kg How can you use the tools available to measure the perpendicular component of r? (This time, limit yourself to only using the vertical line and the horizontal ruler.)
Reconsider the situation given below. If Luis pulls straight down on the end of a wrench that is in the same orientation but is 35 cm long, rather than 20 cm, what force must he apply to exert the same torque? Luis uses a 20-cm-long wrench to tighten a nut, turning it clockwise. The wrench handle is tilted 30° above the horizontal, and Luis pulls straight down on the end with a force of 100 N. How much torque does Luis exert on the nut?
Cole is trying a biceps curl and attempting to lift a 150 N dumbbell. The moment arm of this weight about his elbow joint is 25 cm. The force created by the elbow flexor muscles is 2000 N. The moment arm of the elbow flexor muscles is 2 cm. Is Cole able to lift the weight with this amount of force in his flexor muscles?
The wheels,axle, and handles of a wheelbarrow weigh W=56N. The load chamber and it’s contents weigh WL=635N.the drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward.consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper.find the magnitude of the man’s force for both designs.
A businessman enters the same revolving door on the right, pushing with 547 N of force directed perpendicular to the door and 0.511 m from the hub, while a boy exerts 370 N perpendicular to the door, 1.57 m to the left of the hub. (Indicate the direction with the sign of your answer.) (a) Find the torques exerted by each person.?boy = N · m?man = N · m(b) Find the net torque on the door.?net = N · m
Tweedledum and Tweedledee are carrying a uniform wooden board that is LLL = 3.00 mm long and has a weight of w = 160 N. Tweedledum applies an upward force of magnitude F1 = 60.0 NN at the left end of the board. Which of the following is the correct equation for Στ for the given rotation axis? All rotation axes lie on the x-axis and torques that would cause a counterclockwise rotation are positive. Enter the letter(s) of the correct equation(s) in alphabetical order. For instance, if you thought that choices A, B, and D were correct, you would enter ABD. Answer Choices: Axis of Rotation Et A x=0 (1/2)wL+F2d=0 B x=L (1/2)wL-F2(L-d)-F1L=0 C x=0 (-1/2)wL+F2d=0 D x=d -F1d-F2(d-(1/2)L)=0 E x=(1/2)L (-1/2)F1L+F2(d-(1/2)L) F x=(1/2)L (1/2)F1L+F2(d-(1/2)L)
What is the torque when a perpendicular force of 200 N is applied to a lever arm of 1.2 m? (Instruction: Type your answer without any unit. Type only the number)