A method of analysis yields masses of gold that are low by 0.4 mg. Calculate the percent relative error caused by this result if the mass of gold in the sample is (a) 500 mg (b) 250 mg (c) 150 mg (d) 70 mg

A method of analysis yields masses of gold that are low by 0.4 mg. Calculate the percent relative error caused by this result if the mass of gold in the sample is (a) 500 mg (b) 250 mg (c) 150 mg (d) 70 mg

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter5: Errors In Chemical Analyses

Section: Chapter Questions

Problem 5.8QAP

See similar textbooks

Related questions

Q: The pharmacist attempts to weigh 120 mg of codeine sulfate on a balance with a sensitivity…

A: Maximum weight of codeine sulfate (required) =(120+6)mg=126mg

Q: Standard deviation is an indication of the... a. precision of one measurement b. accuracy of one…

A: Standard deviation:a number which is used to inform how measurements for a group are spread out from…

Q: 15. In preparing a certain ointment, a pharmacist used 28.35 grams of zinc oxide instead of the 31.1…

A: Given, mass of zinc oxide (used) = 28.35 g mass of zinc oxide (required) = 31.1 g

Q: The pharmacist attempts to weigh 80mg of sodium carbonate on a balance having a sensitivity…

A: Maximum weight which can be given is computed as: Maximum weight measured = Actual weight +…

Q: A 795-centigram sample of borax was placed in a certain volume of water at 25 °C. After adding the…

A: A question based on dimensional analysis, which is to be accomplished.

Q: 20 Express the answer to this multi-step calcu- lation using the appropriate number of sig- nificant…

Q: Read the meniscus with the uncertain error range (+/-). ml

A: According to the given image, the meniscus lies in between 5 mL - 6 mL.

Q: n. is the total mass of solid recovered? g is the percent composition of naphthalene in the initial…

A: A) 1.661gm B)21.06% C)15.73%

Q: Which is an example of an indeterminate error? Wrong dilution of sample solution Overshooting…

A: Indeterminate errors are also called accidental errors or random errors which are beyond the scope…

Q: Suggest two sources of systematic error and two sources of random error in measuring the width of a…

A: Error in a measurement is observed when the true measurement value differs from the measured value.…

Q: Express the molecular mass and its standard uncertainty of C17H21NO4 with the correct number of…

A: Answer:- Molecular mass = 17 × mass of carbon atom + 21 × mass of hydrogen + 1 × mass of nitrogen +…

Q: Explain the difference between random error and systematic error.

A: A mistaken result or false result obtained in an experiment or study is termed as error. Error is…

Q: Q2/ The average teacher's salary in a particular state is 54166. If the standard deviation is 10200,…

A: Solution - According to the question - Given - Solution:Given that mean = 54166, sd = 10200 Z =…

Q: What is the uncertainty in a measurement of 0.39 mm?

Q: If you were pipetting 17.0 mL, what is the percent error in the pipet? I know that Volumetric…

A: To figure out percent error in the pipet we need to figure out maximum error in the pipet then we…

Q: calculate its theoretical density in g/cm3. NA put the units

Q: The variance of chemical experiment .data is square of standard deviation

A: The standard deviation and variance are used to measure the scattering of data from the mean value.…

Q: What is a standard deviation in analytical chemistry?

Q: Does standard deviation give a measure of precision or accuracy?

A: Interpretation - Does standard deviation give a mesure of precision or accuracy - Introduction…

Q: A 1.00 m long beam of stainless steel with a square 2.00 cm times 2.00 cm cross section has a mass…

A: Since density of any metal is given by Density = mass of metal / volume of metal

Q: How are systematic method errors detected?

A: Systematic method error is a kind of systematic error. It will have a different calculated mean…

Q: Is it faster to 1) adjust the liquid level to exactly hit a graduated cylinder measurement mark or,…

A: It is nearly impossible to adjust the liquid level to exact mark in graduated cylinder while…

Q: The following prompt will be used to answer the first six questions. An experiment was performed to…

A: Given :

Q: What is the volume in cm3 of a perfect cube if one edge length measures 1.95 m? Group of answer…

A: Given data: The conversion of edge length of cube from meter to centimeter is shown below.

Q: 3. A student weighed an unknown mass directly on an electronic balance of intermediate sensitivity,…

A: Weight of beaker + unknown = 59.121 gWeight of beaker = 30.346 gWeight of unknown = (59.121-30.346)…

Q: 1000 Incorrect! But, you can still earn a point by determining the uncertainty value for the correct…

Q: Which statement is associated with random error?

A: Measured value is the value of a measurement obtained through an instrument or a device. The…

Q: An example of a semiconductor is ZnS with a particle diameter of 1.8 nanometers. Convert this value…

A: Applying basics relationship between nm to dm and nm to inches.

Q: 23.0mL is the measured volume of the crucible. What is the volume in cL?

A: To convert mL to cL , conversion factor is 1 milli liter = 0.1 centi liter 1 mL = 0.1 cL

Q: A method of analysis yields masses of gold that are low by 0.4 mg. Calculate the percent relative…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Reduce the following terms to right number of Significant Figures.…

A: Significant figures are the number of digits in a value, often a measurement, that contributes to…

Q: The standard solution is prepared by dissolving a known mass of zinc pellets with conc. HCl. The…

A: Given information, Volume (V) = 250 mL = 0.25 L Mass of Zn (m) = 0.9809 g Molecular weight of the…

Q: Calculate the percent error when a known value of 5.69 is measured to be 5.85

A: Given,Measured value = 5.85Exact or known value = 5.69Percent error can be calculated as:

Q: .A student estimated that the volume of a crucible was 28.6 mL. When the volume wasaccurately…

A: given, estimated/experimental value = 28.6mL measured/accepted value = 34.5mL

Q: You are given the following data set: 50.3 52.8 60.3 55.4 48.3 35.4 57.6 Please choose the best…

A: As per our community guidelines we can only answer 3 sub-parts of a question, out of all the…

Q: A student calibrated a 10-mL graduated cylinder using water and determined a density of 0.9981 g/mL…

A: Percent error is defined as the absolute value of the difference between the experimental value and…

Q: A student measures the length of an object and obtains 3.65 cm. If thr true value (as reported by…

A: Given, Measured value = 3.65 cm True value = 3.75 cm

Q: The measurements were recorded and then repeated six times for two different methods, each giving:…

A: Given: The sample mean, sample standard derivation ,and sample size 1st method are χ1¯ =42 , s1 =0.3…

Q: Match the following terms with their corresponding definitions: Accuracy How close the measured va…

A: Accuracy = How close the measured value is from the true value.

Q: Explain why materials with very low density exhibit a greater degree of uncertainty in mass when…

Q: A group of students have a 1000-mL beaker with graduation markings every 50 mL and a volume error of…

A: Measuring cylinder of 1000mL with graduation marking of 25mL should be used to accurately measure…

Q: Define the unit of variance?

A: Unit of variance Variance is the average of the squared distances from each point to the mean. the…

Q: The area of an object is calculated from experimental data to be 24.6623 cm2. The t absolute error…

Q: Based on the given data, what is the Àmax of copp 0.1 M Copper 300 0.157 325 0.233 350 0.465 375…

A: Given : We have to tell lambda max for 0.1 M copper.

Q: Give two examples of the Method error (one of the classification of systematic error). Please do not…

A: Method error is caused by the defects in the exoerimental methods.

Q: What is the relative error in the determination of a density for which the accepted value is 0.945…

A: Relative error = |accepted value - experimental value|/accepted value

Q: level of uncertainty

A: LEVEL OF UNCERTAINITY

Q: If the denisty of Platnuim is 19.32 g/cm3 what could the dimnesions of a cube be that weighted 1.00…

Q: A 795-centigram sample of borax was placed in a certain volume of water at 25 °C. After adding the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

The pharmacist weight 800 mg of a substance on a balance of dubious accuracy. When checked on a balance of high accuracy, the weight was found to be 785mg. calculate the percentage error in the first weighing.
In the UV assay of paracetamol you are required to weigh tablet powder “…containing 0.150 g of Paracetamol…”. If the stated content of paracetamol per tablet is 500 mg and the weight of 20 tablets is 11.223 g then the amount of paracetamol tablet powder to be weighed is
In reading the measurements provided by the volumetric apparatus, the eye must be at the same level as that of the meniscus to avoid: Critical ErrorParallel ErrorParallax ErrorOptical ErrorVisual Error
15. In preparing a certain ointment, a pharmacist used 28.35 grams of zinc oxide instead of the 31.1 grams called for. Calculate the percentage of error on the basis of the desired quantity.
5-8. A method of analysis yields masses of gold that are low by 0.4 mg. Calculate the percent relative error caused by this result if the mass of gold in the sample is *(a) 500 mg. *(c) 150 mg. (b) 250 mg. (d) 70 mg.
A group of students took turns using a laboratory balanceto weigh the water contained in a beaker. The results theyreported were 111.42 g, 111.67 g, 111.21 g, 135.64 g,111.02 g, 111.29 g, and 111.42 g.(a) Should any of the data be excluded before the average is calculated?(b) From the remaining measurements, calculate the average value of the mass of the water in the beaker.(c) Calculate the standard deviation s and, from it, the 95% confidence limit.
3. A student weighed an unknown mass directly on an electronic balance of intermediate sensitivity, and got a result of 28.774 g. The student then realized a mistake had been made, and weighed the same unknown by difference on the same balance with the following results:Mass of beaker plus unknown = 59.121 g.Mass of empty beaker = 30.346 g.When the sensitivity of the balance is taken into account, the two values obtained for the unknown mass are considered to be:a. Differentb. The SameExplain your answer.
A loss of 0.4 mL of Zinc occurs in the course of an analysis to determine that element. Calculate the percent relative error due to this loss if the weight of Zinc in the sample is 40 mg.
A method of analysis yields weights for gold that are low by 0.3mg. Calculate the % relative error caused by this uncertainly if the weight of gold is the sample is: A. 800mg B. 500mg C. 100mg D. 25mg
If you were pipetting 17.0 mL, what is the percent error in the pipet? I know that Volumetric pipet with 10.0ml has precision of +-.02 and a Volumetric pipet of 20.0 ml has a precision of +- 0.06, but I'm not sure how to use this information to get the answer.
If 1.5 x 1022 carbon atoms were placed side-by-side in a line, how long would that line be (in feet) if the radius ofa carbon atom is 77 pm? Set up and solve a single step dimensional analysis problem that includes all necessaryfactors.
A standard sample of pooled human blood serum contains 42.0 g of albumin per liter.Laboratory X makes determinations of the albumin concentration on six successivedays. The values obtained are: 41.5 40.8 43.3 41.9 42.2 41.7 g l−1Comment on the bias, precision, and accuracy of the set of results.