a) Name of the Circuit? (Assume Silicon Diodes) [1 Mark]4:1b) Find the peak input voltage to the120 V rmsR.1.0 kfdiodes. [2 Marks]D2c) Find the average output voltage?[1 Mark]d) Find the DC current?[1 Mark]d) Find the Peak Inverse Voltage of the diodes?[1 Mark]e) Draw the output waveform. [1 Mark]eeteeell

It's full wave center tap rectifier.

a) Name of the Circuit? (Assume Silicon Diodes) [1 Mark] 4:1 b) Find the peak input voltage to the 120 V rms diodes. [2 Marks] R. 1.0 kl D2 c) Find the average output voltage? [1 Mar d) Find the DC current? [1 Marl d) Find the Peak Inverse Voltage of the diodes? [1 Marl oL Drovy the output wovoform [1 Morkl eelee

a) Name of the Circuit? (Assume Silicon Diodes) [1 Mark] 4:1 b) Find the peak input voltage to the 120 V rms diodes. [2 Marks] R. 1.0 kl D2 c) Find the average output voltage? [1 Mar d) Find the DC current? [1 Marl d) Find the Peak Inverse Voltage of the diodes? [1 Marl oL Drovy the output wovoform [1 Morkl eelee

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
1 - Do the calculation to predict the expected theoretical output waveform of each circuit shown in Figures 5.4 and Figure 5.6. Assume that the diodes used in the circuit are ideal. ? NOTice that do not copy the answer from and websit even from bartleby beacause there is some one who already post the question on chegg and bartleby but i do not like there answer please and give me your answer if you can answer it thank you on advance
3. What are the main applications of using diodes in commercial power supplies such as laptop power supply? Please provide an original response, thank
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
Answer the following questions according to the above. Remember Kirchhoff's laws when making your calculations in this question. a) According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply? b) According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply? c) Calculate how many values V?−?? are when the zener current is 0 mA. D) Calculate how much the value of ??−?? is when the zener current is at its maximum value.
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
For the following rectifier semiconductor diodes, 1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 download either a group data sheet or individual data sheets from the internet. Then make a comparison table which shows the following for each diode (I-IV). (I) Peak Repetitive Reverse Voltage VRRM (Working Peak Reverse Voltage VRWM DC Blocking Voltage VR) (II) Non Repetitive Peak Reverse Voltage VRSM (half wave, single phase, 50/60Hz) (III) RMS Reverse Voltage VR(RMS) (IV) ADD ANYTHING ELSE YOU SEE FIT. (V) From the table state which diodes you would use for a VRRM of 100V and 1000V (VI) Show a copy of a graph which shows the reverse voltage against typical Capacitance values, say what it shows. (VII) For any of the diodes, describe with the aid of diagrams/illustrations itsapplications in an AC to DC…