) A non-inverting op-amp circuit has the open loop gain of 124 and the resistances R1=1400 N and R2 = .2 kN. Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain (c) Error, when ideal voltage gain is compared with actual voltage gain (d) The percentage error, when ideal voltage gain is compared with actual voltage gain,

) A non-inverting op-amp circuit has the open loop gain of 124 and the resistances R1=1400 N and R2 = .2 kN. Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain (c) Error, when ideal voltage gain is compared with actual voltage gain (d) The percentage error, when ideal voltage gain is compared with actual voltage gain,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

A non-inverting op-amp circuit has the open loop gain of 104 and the resistances R1 = 2k Ω and R2 = 50 k Ω. Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain, and (c) The percentage error, when ideal voltage gain is compared with actual voltage gain.
A non-inverting op-amp circuit has the open loop gain of 136 and the resistances R1=3500 Ω and R2 = 3.8 kΩ . Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain (c) Error, when ideal voltage gain is compared with actual voltage gain (d) The percentage error, when ideal voltage gain is compared with actual voltage gain. (a) The actual value of voltage gain Answer for part 1 (b) The ideal value of voltage gain Answer for part 2 (c) Error, when ideal voltage gain is compared with actual voltage gain. Answer for part 3 (d) The percentage error, when ideal voltage gain is compared with actual voltage gain.
q23/ A non-inverting op-amp circuit has the open loop gain of 257 and the resistances R1=4.1 kΩ and R2 = 6860 Ω . Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain(c) Error, when ideal voltage gain is compared with actual voltage gain and The percentage error, when ideal voltage gain is compared with actual voltage gain.
1. The virtual short is applicable A. If one of the input is tied to the ground B. Only if there is a feedback C. All the time D. Depending on the components used 2. What ideal characteristic of Op-Amp contributes to the Virtual Short concept? A. Zero Ohm Input Resistance B. Zero Ohm Output Resistance C. Input terminals do not let current to flow D. Infinite gain 3. Op-amp closed loop gain varies A. True B. Depending on the resistor values used C. Not applicable D. False
1. Assuming the op amp to be ideal, derive an expression for the closed-loop gain of the circuit shown in Figure 1.
Q 1) For the given circuit shown in Figure 4.1: (i) Provide the name for this op-amp circuit configuration and use the ideal op-amp assumptions to solve for the output voltage in terms of the input voltages and resistors. (ii) What is the input resistance seen by ?0, V1 and V2. ?
Figure Q2(a) shows an amplifier system with the given input voltagewaveform Vin and the corresponding output voltage waveform Vout. If a practical op-amp is used in the amplifier system in Figure Q2(a),calculate the closed-loop gain, ACL given that the open-loop gain, AOL =3000. You can use the value of resistances found in Q2(a)(i).
Please answer this two part question A) It is known that when an Op-amp is operated using the negative feedbackconfiguration, the output impedance reduces. Derive an expression that proves this. B) It is known that when an Op-amp is operated using the positive feedbackconfiguration, the output impedance increase. Derive an expression that proves this.
Based on the simulation’s results, explain the function of a differential amplifier. (Hints: comment on the shape of Vo1 and Vo2, explain what would happen if V1 and V2 were the same, reflect on why it is important that an ideal op-amp has infinite input impedance).
Activity 2:You are asked to examine the performance of three op-amp circuits. 2-A) Categorize the circuits in terms of using a feedback or not, and the specific type of thefeedback connection (positive or negative, shunt or series, voltage or current).2-B) Explain the principle of operation of Circuit A. Explain limitations of this circuit in termsof practical applications. What is the technical name describing this circuit?2-C) Explain the principle of operation of Circuit B. What is the advantage of this circuitcompared to Circuit A? What is the technical name describing this circuit?2-D) Explain the principle of operation of Circuit C. What is the advantage of this circuitcompared to Circuits A and B? What is the technical name describing this circuit?2-E) Draw the block diagram of Circuit C and define the forward path gain A and feedbackpath gain β. Derive the overall circuit gain relating input to output.2-F) Build all circuits in MultisimTM using one ‘uA741CP‘op-amp IC fed by…
Explain how you would determine the gain of an op-amp circuit (shown below) from measurements. Specify what equipment you would use and why, along with where/how you would make measurements. Be explicit. Text answers only.
Question 1: a. For the circuit shown, determine V0 when R1 = 1.8 kΩkΩ, R2 = 80 kΩ, Vx = 100 mV, Vy = 10 mV, and Vcc = 15V. b. For the circuit shown, determine R1 such that V0=m×(Vx−Vy). Assume mmm = 5.0 and R2 = 50 kΩ and that the op-amp is in its linear region of operation.