A non-rotating shaft made of 1030 CD steel is subjected to static loads 320lb and 340lb at points C and D, respectively, while being supported by bearings at

Q: find value of Mmax

A: 100KN/m, so for 4 m beam its will be 400KN which is acted at mid of UDL.to find the maximum bending…

Q: 3 m B -3 m- -3 m- C 2.25 m k = 200 N/m- -3 m D E 4 m F 3 m 3 m 3 m 3 m A -0-90° p=0.1 -2m-1m- F(x)=…

A: Fx=e-lnxelnx+e-lnx+lncos-11-sin2xx N/cm

Q: 10. For the following gear train, if the speed of the input shaft is 1500 rpm CW, find the speed and…

A:

Q: In the figure below the shaft is simply supported in ball bearings at A and D. The shaft rotates and…

A:

Q: The pulley and gear are subjected to the loads shown. For these forces, determine the equivalent…

A: Various forces acting on pulley-gear system are :-F1=680 N ; F2=150 N ; F3=1155 N

Q: For a 3-dimensional free-body diagram, when all of the forces pass through one point as shown in…

A: ▪︎When the line of action of all the forces passes through the one single point, then it is known as…

Q: Calculate the fiber volume fraction required in a certain unidirectional E-glass fiber reinforced…

A: volume fraction of fibers=Vf=92% Assuming that remaining % is carried by matrix=8% tensile stregth…

Q: for Part V) should the answer not be -0.4 to the final part of the question since the number put…

A: We have, general equation of the system as x=4.23sin100πt-1.79cos100πt We can write it in the…

Q: Turnbuckle T₁ is tightened to a tension of 160 lb and turnbuckle T₂ is tightened to 98 lb. Determine…

A: As per the Bartleby code of conduct, it is recommended to answer the three subparts of a multiple…

Q: Calculate the time required for completing

A: Given DataDepth of cut d = 5 mmwith  w = 150  mmLength of the elate l= 600 mmThickness t = 25…

Q: The drag force (Fdrag) exerted by air on a moving car depends on a dimensionless drag coefficient…

A:

Q: Determine the force in each member of the loaded truss. All triangles are isosceles. Forces are…

A:

Q: Show complete solution, including the process of integration, solving for the area/moment of the…

A: Fx=e-lnxelnx+e-lnx+lncos-11-sin2xx N/cm

Q: Create a shear force and bending moment diagram. From the equations and/or the plot, determine the…

A: The values are F=100 N,qo=10 N/m, a=1 m, b=1 m In the question, value of b is not given, we have…

Q: A composite material that has boron fibers coated in aluminum has a density of 2.65 g/cm^3. The…

A: The volume of the matrix.Given:The density of the material is .The density of the fibers is .The…

Q: The 5.7-lb force is applied at point A of the crank assembly. Determine the moment of this force…

A:

Q: The piece of plastic is originally rectangular. Suppose that a = 330 mm and b = 420 mm .(Figure 1)…

A:

Q: 3m B -3 m -3 m C 2.25 m k = 200 N/m -3 m- D 4 m- F 3m 3 m 3m 3 m A -0-90° p=0.1 -2m-1m- F(x)= e-Inx…

A: Fx=e-lnxelnx+e-lnx+lncos-11-sin2xx N/cm

Q: Determine conductive resistance (in K/W) of a 80 m^2 plane wall composed of 2 layers:

A:

Q: As shown, a load of magnitude P is applied to a structure. Assuming that all members are weightless…

A:

Q: For the beam and loading shown, determine the maximum normal stress due to bending on section a-a.…

A:

Q: the pressure and temperature at the end of the heat-addition process, (b) the net work output, (c)…

A: From the temperature, the relative specific volume and internal energy at inlet conditions can be…

Q: What is the functional difference between an accumulator and an ABS fluid accumulator? (70-100…

A: To explain:

Q: 2. The table below shows experimental data for the shape and pressure distribution on the upper and…

A: The central difference for the numerical derivatives are dYudx=Yui+1…

Q: Question 6 A liquid flows down an inclined plane surface in a steady, fully developed laminar film…

A: For solution refer below images.

Q: Answers: R- 200 mm 80 mm (629 Moi 325 mm 10° 40.11 110 1155 N mm i + i 680 N 150 N i+ -394 + i…

A:

Q: Q.4: Design a wire rope for an elevator (Miscellaneous hoists) in a building of (60 m) height, for a…

A: Given Data; Height of the building (H) = 60 m Total load (W) = 20 kN = 20,000 N Speed of the…

Q: 4. If the bearing pads at A and B support only vertical forces, determine the greatest magnitude of…

A: The bending stress allowable is σallo=15 MPa The shear stress allowable is τallow=1.5 MPa

Q: EXERCISE 1 A car is in motion along a horizontal straight line. The brakes of the car are applied,…

A: The initial velocity of the car as "v₀," the final velocity as "vf," the acceleration as "a," and…

Q: the space between two square flat parallel plates is filled with oil .Each side of the plate is 50…

A:

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: The linkage is made of two pin-connected A-36 steel members, each having a cross-sectional area of…

A:

Q: A chromel–constantan thermocouple measuring the temperature of a fluid is connected by mistake with…

A:

Q: Ross and Rachel are fighting if they were on a break. Ross is trying to get his stuff weighing 150.…

A:

Q: hey had given wings with the cross sectional area of 10m^2 and answer this questions  1a) Describe…

A:

Q: Method of join: get the force in each node 5N FI. Cap screw 5m/ Gm CB ION -F₂=3N Roller R

A:

Q: A. Draw the shear force and moment diagrams of the beam. B. Locate the centroid (take the reference…

A: Given:Cross section made up of = 280 mm x 32 mmallow = 15 MPaTo find:Bending stress and Transverse…

Q: What is the minimum length of fibers to ensure effective load transmission called? Answer:

A: Fibers are used in additive manufacturing for layering

Q: If the rod AB is rotating with an angular velocity AB = 3 rad/s in the direction shown, determine…

A:

Q: ꜱᴛᴇᴀᴍ ᴇɴᴛᴇʀꜱ ᴛʜᴇ ᴛᴜʀʙɪɴᴇ ᴀᴛ 2.2 ᴍᴘᴀ ᴀɴᴅ 250°ᴄ. ꜰᴇᴇᴅᴡᴀᴛᴇʀ ᴇɴᴛᴇʀꜱ ᴛʜᴇ ꜱᴛᴇᴀᴍ ɢᴇɴᴇʀᴀᴛɪɴɢ ᴜɴɪᴛ ᴀꜱ…

A: Steam enter turbine at 2.2MPa and 250'C Saturated liquid 30'C

Q: Q3. For the thin walled single rectangular beam and loading shown, determine the shear flow…

A: Due to vertical symmetry of the cross section, the shear center will lie on the centroidal y axis,…

Q: Replace the loading on the beam by an equivalent resultant force. (Figure 1) Suppose that w₁ = 3.0…

A:

Q: Study of pressure and pressure measurements: kPa 101.325 mm of Hg 760 latm 100 kPa 76 cm Hg 1…

A: Here, the given table:   kPa mm of Hg millibar Psi 1 atm         100 kPa         76 cm Hg…

Q: Find the differential equations for modeling the given system. Draw the modeling according to the…

A: Given Data: k1=12k2=14   To Find: Determine the two differential equations of motion of the system.

Q: The capacity of the fixed-fixed beam 3-4 needed to be increased. It was decided that this can be…

A: There is fixed beam which is uniformly distributed throughout the beam.And the mid span deflection…

Q: Considering the following 2nd order differential equation that will be used to model a plane wall…

A: It is asked to analyze the role of FEA to solve differential equations in complex geometries

Q: 2. Which of the following shows the correct equilibrium equation in the direction parallel to the…

A: Force applied by Ross parallel to inclined plane=150N Force applied by Rachel normal to inclined…

Q: Problem 1: A circular shaft with a diameter of 100 mm and a length of 2 meters is subjected…

A: Probelm 1. Diameter D=100mm , Length L=2m , G=80GPa , Torque T=500NmProblem 2. Diameter D=80mm ,…

Q: 1. What type of linear two-dimensional element do you recommend discretizing the curved boundary in…

A: A small element of a body can be represented by a mesh configuration. These mesh configurations can…

Q: (b) There are three vessels; A, B, and C which are connected together through some closed valves.…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.