Delermine the average normal stress in the aluminum due to this loading The A-36 steel pipe in (Figure 1) has a 6061-16 aluminum core It is subjected to a tensile force of 200 kN. The pipe has an outer diameter of 63 mm and an inner diameter of 53 mm. For A-36 steel, En = 200 GPa and for 6061-T6 aluminum, E = 68.9 GPa Express your answer to three significant figures and include appropriate units. ? Value Units Submit Reguest Answer Determine the average normal stress in the steel due to this loading Figure (1 of 1 Express your answer to three significant figures and include appropriate units. 400 mm 200 kN + 200 kN Value Units

Delermine the average normal stress in the aluminum due to this loading The A-36 steel pipe in (Figure 1) has a 6061-16 aluminum core It is subjected to a tensile force of 200 kN. The pipe has an outer diameter of 63 mm and an inner diameter of 53 mm. For A-36 steel, En = 200 GPa and for 6061-T6 aluminum, E = 68.9 GPa Express your answer to three significant figures and include appropriate units. ? Value Units Submit Reguest Answer Determine the average normal stress in the steel due to this loading Figure (1 of 1 Express your answer to three significant figures and include appropriate units. 400 mm 200 kN + 200 kN Value Units

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
Bar A was manufactured 2 mm less than bar B due to an error. The attachment of these bars to the rigid bar wouldcause a misfit of 2 mm. Calculate the initial stress in each assembly. Which of the two assembly configurationyou would recommend? Use modulus of elasticity of E = 80 GPa and diameter of the circular bars as 32 mm.
A steel rod of 30 mm diameter is inserted in a copper tube of external diameter 45 mm and an internal diameter of 37 mm carries a load of W =1750kN. The length of this compound bar is 180 mm. If, ES= 2 × 105 N/mm2and ECu= 1 × 105 N/mm2, calculate the stresses developed in copper and steel.
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
Strength of materials - ENGR 3321 The answer should be: 17.68 kN; 11.8 MN/m2 compressive
A simply supported beam having a span of 12 m carries a uniform dead load of 5.8 kN/m and a live load of 8.8.kN/m in addition to a concentrated dead load of 22 kN applied at its midspan. The beam has a width of 350 mm and an effective depth of 525 mm. Total depth of beam is 625 mm. it is reinforced with a tensile steel of 3040 mm2. a) Compute the cracking moment. b) compute the instantaneous deflection c) compute the immediate deflection due to sustained load d) Compute the total deflection after 5 years with a dependent factor of 2.0.
A steel rod with a cross sectional area of 120〖mm〗^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? α=11.7x〖10〗^(-6)/°C and E = 200GPa. See figure 06
The steel channel is used to reinforce the wood beam. Determine the maximum stress in thesteel and determine the maximum stress in the wood if the beam is subjected to a moment of M=1.2kN.m Est = 200GPa, Ew12GPa.
A high-strength steel band saw, 27 mm wide, runs over pulleys 1100 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E = 210 GPa. Answer must be in mm.
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
A storage tank of air, 30 inches in diameter, is to withstand an internal pressure of 180 psi with a design factor of 3.5 based on ultimate stress. The steel has the strength equivalent of C1020 annealed and the welded joints should have a relative strength of 92%. Note: ultimate stress of for annealed C1020 steel is 50 ksi. Compute for longitudinal stress of the tank. a.13, 171 psi b.13, 786 psi c.12,893 psi d.12,860 psi