A person is recording measurements from an analog data reader. During the first reading, he was not looking at the meter from a straight angle. He gets the reading of 72. At a second reading later he looks straight at the machine and gets the reading of 70. a) Which reading number is nearer to the actual value? b) What is the error type that happened in that reading? c) Suppose the data reader becomes faulty due to the extreme heat and gives a third measurement of 65. What type of error happened now? d) The data reader is working properly now, but there is a slight difference between two readings for the same measure. What type of error happened now and how can we minimize it?

A person is recording measurements from an analog data reader. During the first reading, he was not looking at the meter from a straight angle. He gets the reading of 72. At a second reading later he looks straight at the machine and gets the reading of 70. a) Which reading number is nearer to the actual value? b) What is the error type that happened in that reading? c) Suppose the data reader becomes faulty due to the extreme heat and gives a third measurement of 65. What type of error happened now? d) The data reader is working properly now, but there is a slight difference between two readings for the same measure. What type of error happened now and how can we minimize it?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Create a sequence detector that detects the sequence 1001 or 0110 by using Verilog Code. Construct the modules for both the Moore and Mealy models. Demonstrate your simulation results using the following input sequence for the test fixture (test bench): x= 0010011010010110010110110100
Ripple counters are also called O a. VLSI counters O b. Asynchronous counters SSI counters O d. Synchronous counters Given in the figure is PLA circuit, used to imnlement the Pooloan fu
Test the accuracy of the equation by applying the operation in Ampere law (del.)? If there is a mistake, correct this mistake.
What does the data become after Quantization (remember to round the numbers)?
Shown in the figure is timing diagram of a T-FF. Using the timing diagram determine which type of clock is used Q a. Anegative (low) clock pulse O b. Anegative edge triggered clock 67 O c. Apositive edge triggered clock O d. Apositive (high) clock pulse
Problem #3: board has three clocks that can be seen in the table below: Table 3-2 Pin Assianment of Clock Inputs Description Signal Name ADC CLK_10 MAX10_CLK1_50 VO Standard 10 MHz clock input for ADC (Bank SB) 50 MHz clock input(Bank 38) 50 MHz clock inpu(Bank 38) 3.3-V LVTTL 3.3-V LVTTL 3.3-V LVTTL MAX10_CLK2_50 You need a clock of 1.25 MHz for your circuit, and for that reason you are going to use a Ipm_counter as a frequency divider shown here: Panmete Value LPM SVALUE LIM AVALUE LPM MODULUS LIM ORECTION LPM WIDTH PM PORT UPDOWN LPM_COUNTER be find (a) LPM_MODULUS and (b) the minimum width of q[..] LPM_WIDTH. (c) What bit of q[..] you will pick as your 1.25-MHz clock?
Calculate the value of Xc for the circuit. Please show work. I will give you a thumbs up.
Identify the component which is not available in digital Voltmeter? a. Clock generator b. ADC c. Comparator d. 7-segment to BCD
If you can, I need a sample answer with clear details because I want to understand the answer very well. This question from measurements instrumentation course. Thx??
We write the following code to configure a time delay of around 0.25 seconds. LDI R17, 0XDF L1: LDI R16, Value L2: NOP NOP NOP NOP DEC R16 BRNE L2 DEC R17 BRNE L1 We assume 1MHZ clock frequency. Which of the following is correct ? Select one: a. Value = 217 b. Value = 190 c. Value = 178 d. None of the Above
2. Which of the symbols in Figure A6 represents a circuit breaker with thermal overload protection?A. CB. DC. AD. B
Can you show this work written out and not typed, please and thank you!