For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a special fluid of SG=0.965, determine the pressure head at section 1. 550mmo 7.88m 2 2.95m Datum Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3 13.944

For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a special fluid of SG=0.965, determine the pressure head at section 1. 550mmo 7.88m 2 2.95m Datum Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3 13.944

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
The figure shows a siphon that is used to draw waterfrom a large open tank. If the absolute vapor-pressureof the water is pv = 1.23 kPa. (a) determine the shortest drop length L of the50-mm-diameter tube that will cause cavitation in thetube. Show all your calculations. (b) Also draw the energy and hydraulic grade lines forthe length of the tube. Be sure to indicate the pressureheads, elevation heads, and dynamic heads. And toshow all your calculations.
10.4 Determine the pressure difference between two points on either side of a sudden enlargement from a tube with a 2-in ID to one with a 6-in ID when the velocity of flow of water is 4 ft/s in the smaller tube. 10.5 Determine the pressure difference for the conditions in Problem 10.4 if the enlargement is gradual with a cone angle of 15. Answer: p1-p2= -0.0891 psi
The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.
Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
Determine the discharge in gallons per minute of a new 16-in cast-iron pipe if the friction losa is 5 lb per so in. per 1000 ft and the liquid is: (a) water at 60. F; (b) & heavy fuel oil at 60° F. Answer should be : 4640 and 3100 Show your handwritten solution, thank you.
In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be 39.8 ft3 /s. The leakage into the tailrace was found to be 1ft3 /s. The elevation of the centerline of the shaft above, the surface of tailwater was 12.67ft. The diameter of the turbine intake was 30in and the pressure at this section was measured by a mercury U-tube. The readings in the two sides of the mercury U-Tube were 10.556 ft and 0.900 ft, the zero of the scale being at a level 3.82ft below that of the centerline of the turbine shaft. The generator output was 391.8 kW, friction and windage loss 13.8 kW, iron loss 2.0kW and armature loss of 4.4kW. The specific gravity of the mercury used was 13.57. Calculate the efficiency of the turbine.
A smooth plastic pipe is to be designed to carry 10 (ft^3)/s of water at 77°F(25°C) through 1800 ft of horizontal pipe with an exit pressure at 25 psig. The pressure drop is to be approximately -300 psig. Determine the minimum pipe diameter (in inches) that will result in the given pressure drop. For water at 77°F: ρ = 1.934 slug/(ft^3), and μ = 1.86E-5 slug/(ft-s). Round your answer to 2 decimal places.
The tank–pipe system of Fig. is to deliver at least11 m3/h of water at 20°C to the reservoir. What is themaximum roughness height ε allowable for the pipe?
For the piping system of Fig. , all pipes are concretewith a roughness of 0.04 in. Neglecting minor losses, computethe overall pressure drop p1 - p2 in lbf/in2 ifQ =20 ft3/s. The fluid is water at 20°C.
PROBLEM 3: A venturi meter with a throat diameter of 6 cm is fitted in a horizontal pipeline of 12 cm diameter with oil of specific gravity 0.88 flowing from left to the right. The difference in level in the two limbs of a mercury manometer connected to the tapping points read 12 cm and the connecting pipes are filled with the same oil. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa.
Determine the flowing bottomhole pressure required for a well completed with 3.5 inches tubing set at 12,500 ft depth to produce 400 BPD of 7,500 cuft/bbl crude oil if the tubing head pressure is set at 125 psig.