A plane wall of thickness 5cm and k-25 W/m.K contains a uniform heat source of 2x107 W/m³. The environment at the sides of the wall are (h-3200 W/m².K, T.-130 °C) and ( h-1600 W/m².K, T.-140 °C) respectively. Determine: 1. The Surface temperatures of the wall. 2. The maximum temperature in the wall, and its location.

A plane wall of thickness 5cm and k-25 W/m.K contains a uniform heat source of 2x107 W/m³. The environment at the sides of the wall are (h-3200 W/m².K, T.-130 °C) and ( h-1600 W/m².K, T.-140 °C) respectively. Determine: 1. The Surface temperatures of the wall. 2. The maximum temperature in the wall, and its location.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.29P: 1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that...

See similar textbooks

Similar questions

A cooling system is to be designed for a food storage warehouse for keeping perishable foods cool prior to transportation to grocery stores. The warehouse has an effective surface area of 1860 m2 exposed to an ambient air temperature of 32C. The warehouse wall insulation (k=0.17W/(mK)) is 7.5 cm thick. Determine the rate at which heat must be removed (W) from the warehouse to maintain the food at 4C.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
1.29 A spherical interplanetary probe with a 30-cm diameter contains electronic equipment that dissipates 100 W. If the probe surface has an emissivity of 0.8, what is its surface temperature in outer space? State your assumptions in the calculations.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
Consider a person standing in a breezy room at 20°C. Determine the total rate of heat transfer from this person if the exposed surface area and the average outer surface temperature of the person are 1.6 m2 and 29°C, respectively, and the convection heat transfer coefficient is 6 W/m2 ·°C (Fig. 2–75).
The temperature of a cylindrical tank containing liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The amount of heat lost by convection and radiation from the tank to the environment is 65.5 W / m. Calculate the temperature of the environment where the tank is located: h = 4.35 W / m2K, ∈ = 1.
1. A 1000-W iron is left on the iron board with its base exposed to the air at 20°C. The convection heat transfer coefficient between the base surface and the surrounding air is 35 W/m². °C. If the base has an emissivity of 0.6 and a surface area of 0.02 m², determine the temperature of the base of the iron. 2. The inner and outer surfaces of a 5-m x 6-m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m °C are maintained at temperatures of 20°C and 5°C, respectively. Determine the rate of heat transfer through the wall, in W.
Because you forgot to let the pipes drip during a freezing night, a section of an outdoor pipe is now frozen. The frozen section is L = 1 m long and the inner pipe diameter is D = 1.8 cm. During the day, the pipe is exposed to the cold air, the Sun, and the radiating surroundings. The cold air temperature is T∞ = -10°C, and has convection heat transfer coefficient h = 20 W/m2·K. The Sun provides solar irradiance of Gsun = 1350 W/m2. The steel pipe surface has absorptivity α = 0.6 and emissivity ε= 0.1. The surroundings, such as vegetation, houses, ground, etc. can be assumed to be blackbody held at Tsur = 280 K. A) Using the energy conservation system illustrated below, establish an equation that describes the stored energy in the section of frozen water (Est). B) Determine the amount of time needed to melt the ice in the pipe. Ice has density ρ= 920 kg/m3, and latent heat of fusion hsf = 334 kJ/kg. The ice is Tw = 0°C. Ignore conduction through the pipe walls – assume the pipe…
An average person generates heat at a rate of 240 Btu/h while resting in a room at 70°F. Assuming onequarter of this heat is lost from the head and taking the emissivity of the skin to be 0.9, determine the average surface temperature of the head when it is not covered. The head can be approximated as a 12-in-diameter sphere, and the interior surfaces of the room can be assumed to be at the room temperature.
A Gasoline engine operating on an air standard condition has a clearance volume of 15cm^3 and a displacement volume of 100cm^3. Determine the theoretical thermal efficiency of the engine.