A planetary gear train is shown. The ring gear has 50 and is not able to rotate. The number of teeth on the planet gears is 11. If the sun gear has 19 teeth and is driven at a speed of 95 rpm, determine the gear ratio of the gear train if the output is the rotational speed of the arm/carrier. Answer:

A planetary gear train is shown. The ring gear has 50 and is not able to rotate. The number of teeth on the planet gears is 11. If the sun gear has 19 teeth and is driven at a speed of 95 rpm, determine the gear ratio of the gear train if the output is the rotational speed of the arm/carrier. Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A two-start worm gear that is rotating at 800 rpm drives a 26-tooth worm gear. The worm gear has a pitch diameter of [46] mm and a pitch of [14] mm. If coefficient offriction (u) is 0.06, (i) Determine the helix angle of worm gear. (ii) Determine the speed of gear. (iii) Compute the distance of gear. (iv) Identify the maximum gear efficiency of this transmission system
An epicyclic gear consists of ring gear, planet gear and sun gear. The ring has 72 internal teeth and sun gear has 32 external teeth . Planet gear meshes with both ring and sun gears and carried an arm which rotates about the centre of the ring gear at 20 r.p.m . If the gear A is fixed. Calculate the speed of planet gear.
The max speed for the servo shown is 130RPM when connected to 6V. Assume that the gearbox on your servo is able to output a torque of 1.5 kg-cm while turning at this speed. Using the number of teeth on each gearprovided in the table, determine the torque and rotational speed of the output shaft on the DC motor. HINT: Work backwards from the output shaft and use the equations developed in class that relate the number of teeth to the torque. When working back from the output shaft to gear 7/6, realize that the “torque” transmitted by gear 7 is the SAME as the torque transmitted by gear 6 since they are joined. Then, relate the torque of gear 6 to gear 5 based on their numbers of teeth. Since gears 5 and 4 are actually one piece, the torque in 4 and 5 will be the same (as was the case for gears 6 and 7). Repeat for the other gears, working your way all the way back to the DC motor.
Two mating involute spur gear of 20° pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of the teeth is 12 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length, find : a. The addendum for pinion and gear wheel; b. The length of the arc of contact; c. The maximum velocity of sliding during approach and recess. Assume pinion to be the driver.
The drawing represents a planetary reduction gear used in aeronautics. Calculate the speed of the satellite propeller (4) if motor 3 is running at 1200 RPM. Z1 = 50 teeth; Z2 = 18 teeth; Z3 = 90 teeth
A pair of gears having 40 and 20 teeth respectively are rotating in mesh, the speed of the smaller being 2000 rpm. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 20° involute form, addendum length is 5mm and the module is 5mm.Also find the angle through which the pinion turns while any pairs of teeth are in contact.
The pitch circle diameter of the smaller of the two spur wheels which mesh externally and haveinvolute teeth is 100 mm. The number of teeth are 16 and 32. The pressure angle is 20° and theaddendum is 0.32 of the circular pitch. Find the length of the path of contact of the pair of teeth.
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm and Gear D is the output gear for this simple gear train. The number of teeth for each gear is as follows: NA = 116 Teeth, NB = 178 Teeth, NC = 70 Teeth and ND = 120 Teeth Calculate the output angular velocity at Gear D (ωD). Give your answer in rads-1to the nearest radian.
The motion transmitted between the teeth of gears in mesh is *
Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm. The number of teeth for each gear is as follows: NA = 60 Teeth, NB = 84 Teeth, NC = 36 Teeth and ND = 60 Teeth.Calculate the output angular velocity at Gear D (ωD).Give your answer in rads-1 to the nearest radian. Gear D is the output gear for the simple gear train shown below.
Consider the epicyclic gear system. Set up a tabke of wheel speeds for the cases where all the wheels rotate..Consider the same system with the sun wheel S as the input and the annulus A as the output.The diameters of the sun andbplanet wheels are 150mm and 75mm,respectively. I the sun wheel runs clockwise at 1000 rev/min and output to input ratio Na/Ns is -1,determine the speeds of the arm L and the planet wheel P.