Q6/ An epicyclic gear train shown, the gears A and B are internal gears and the gear C-D is a compound gear. The gears E and F have the same pitch and number of teeth (Te= Tr= 18), Te 28 and Ta 26. (1) Find the number of teeth on A and B; (2) If the arm G makes 100 rpm clockwise and A is fixed, find the speed of B; and (3) If the arm G makes 100 rpm clockwise and wheel A makes 10 rpm counter clockwise find the speed of wheel B. (Note A and B not a compound gears)

Q6/ An epicyclic gear train shown, the gears A and B are internal gears and the gear C-D is a compound gear. The gears E and F have the same pitch and number of teeth (Te= Tr= 18), Te 28 and Ta 26. (1) Find the number of teeth on A and B; (2) If the arm G makes 100 rpm clockwise and A is fixed, find the speed of B; and (3) If the arm G makes 100 rpm clockwise and wheel A makes 10 rpm counter clockwise find the speed of wheel B. (Note A and B not a compound gears)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
(Q.1) A compound epicyclic gear is shown in Fig. for Q.1. The shaft P is drivenat 3000 rev/min while the annulus A2 is driven at 1000 rev/min in theopposite direction. The numbers of teeth in the gears are S1, 16; S2,24; A1, 60; A2, 90. Determine the speed and direction of rotation ofshaft Q. (Q.2) A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
Figure shows an alicyclic gear train with the following details:A has 40 teeth external (fixed gear) ; B has 80 teeth internal ; C - D is a compound wheel having 20 and 50 teeth (external) respectively, E-F is a compound wheel having 20 and 40 teeth (external) respectively, and G has 90 teeth (external). The arm runs at 100 r.p.m. in clockwise direction. Determine the speeds for gears C, E, and B.
A reverted gear train with a speed ratio of 12 consists of four gear wheels. Gear A has a module pitch of 3mm and is meshed with gear B. Whereas gear C that is meshed with gear D has a module pitch of 2.5mm. Gear B and C form a compound gear system. The distance between axis of rotation of driving gear A and driven gear B is equal to 200mm. If gear A has 24 teeth, determine the suitable number of teeth for all gears.
In a brick-making machine is found this train of gears. A motor carrying pulley E, which is 8 in. in diameter, drives the machine. The wide-faced roller F, 14 in. in diameter, drives a conveyor belt. If the motor runs at 1500 rpm. what is the speed of the conveyor belt in ft. per minute? (Neglect the thickness of the belt).
A pinion having 30 teeth, a module of 2 mm, and rotating at 2000 rpm is to drive a gear rotating at 500 rpm.a) Determine the diametral pitch,b) Number of teeth in the gear, and the center distance.
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. b)Show the useful working length and the limit working length on the figure
A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal pressure angle, and 3 mm normal module. The wheels are to have 26 and 34 teeth, and to work with a centre distance of 146 mm. Calculate the transverse pressure angle in degrees.