Using the data below, calculate the following for all gear settings and list the results in a table form: The speed ratio of the MM245 Automotive gearbox. The input and output torque. The input and output power. The efficiency of the gear system. Gears Input Speed (rpm) Output Speed (rpm) Input Torque (N.m) Output Torque (N.m) 1 322 97 2,67 0,72 2 320 168 3.05 1,23 3 311 238 4,24 1,83 4 297 297 5,95 2,36 5 280 334 7,36 2,80 The moments of inertia of the parts attached to the input shaft A is 0.019 kgm2 and that of the parts attached to output shaft B is 0.1 kgm2. If input shaft A exerts a constant torque of 7.27 Nm and is geared to output shaft B, calculate the following: The gear ratio gives the maximum angular acceleration of output shaft B. The corresponding angular acceleration of each shaft.

Using the data below, calculate the following for all gear settings and list the results in a table form: The speed ratio of the MM245 Automotive gearbox. The input and output torque. The input and output power. The efficiency of the gear system. Gears Input Speed (rpm) Output Speed (rpm) Input Torque (N.m) Output Torque (N.m) 1 322 97 2,67 0,72 2 320 168 3.05 1,23 3 311 238 4,24 1,83 4 297 297 5,95 2,36 5 280 334 7,36 2,80 The moments of inertia of the parts attached to the input shaft A is 0.019 kgm2 and that of the parts attached to output shaft B is 0.1 kgm2. If input shaft A exerts a constant torque of 7.27 Nm and is geared to output shaft B, calculate the following: The gear ratio gives the maximum angular acceleration of output shaft B. The corresponding angular acceleration of each shaft.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter38: Manual Transmissions And Transaxles

Section: Chapter Questions

Problem 5ASRQ: Technician A says that if a single idler gear is used to obtain reverse gear, its size and number of...

See similar textbooks

Similar questions

Examine the gear drive system shown below. All the gears have a DP = 12. The smallest gear is the primary driver gear and has 15 Teeth, RPM = 3600, and Torque = 2.2 N-m. That small gear meshes with a 72-tooth gear which is connected to another gear that has 20 teeth. That 20-tooth gear connects to the final driven gear that has 64 teeth. What is the TOTAL Gear Ratio for this system? What is the TOTAL Speed Ratio for this system? What is the Center to Center spacing of the first gear set? What is the Center to Center spacing of the second gear set? What is the final output RPM of the 64-tooth gear? What is the final output Torque supplied by the 64 tooth gear?
The total conversion rate of a two-stage gearbox is 53, the conversion rate of the second stage is 1.5 times the conversion rate of the first stage. If the number of teeth of the gear mounted on the input shaft is z1=27 and the number of teeth of the pinion of the second stage is z3=33, how many teeth are the gear z2 of the first stage?
Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear? (Hint: If your ID is 114-2020, then compression force would be 114 N)
Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear?
Find the diameter of each gear using one simple gear train with 4 gears that work as a speed reducer with a ratio of 5:1 Input of 100 rpm, Output of 20 rpm. Consider number of teeth as: N1=20 N2=40 N3=80 N4=100 Use module of 2
Please help with homework NB:Also show me the gear train ratio, output speed of gear D, torque available on the output shaft, distance between the shafts for Gears C and D [mm],
Figure shown below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts Band C, nine speed changes can be obtained as shown in Table given below. The problem of the machine tool designer is to select tooth numbers for the various gears (2 to 10) so as to produce a reasonable distribution of speeds for the output shaft. The gears 2, 6 and 9 are having 20, 25 and 50 teeth respectively. The input shaft speed is 450 rpm and the output speed can vary from 137 rpm to 580 rpm depending on the sequence of the gears. If the output speed obtained through the gear sequence 2-5-5-8 is 257 rpm and if the minimum and maximum number of teeth in the gear system are 20 and 50 respectively, (i) Suitable tooth numbers for the remaining gears (3,4,5,7,8 & 10)
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise.a) By calculating gear sizes; Draw in 1:1 scale.
You are a gearbox manufacturer designing a conventional (reverted) speed reduction gear box with a total reduction of 1875:1. Your maximum gear ratio per stage is 5:1. What is the minimum number of gear stages that are required. Please add a number only, if you think it is 2 stages than simply type 2.
Two involute gears of 20-degree pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5mm and the pitch line speed is 1.2m/s, assuming addendum as standard and equal to one module. Find a.) The angle turned through by pinion when one pair of teeth is in mesh and b.) The maximum velocity of sliding.
7. The following data relate to a pair of 20° involute gears in mesh : Module = 6 mm, Number of teeth on pinion = 17, Number of teeth on gear = 49; Addenda on pinion and gear wheel = 1 module. Find : (a) The number of pairs of teeth in contact (b) The angle turned through by the pinion and the gear wheel when one pair of teeth is in contact (c) The ratio of sliding to rolling motion when the tip of a tooth on the larger wheel (i) is just making contact (ii) is just leaving contact with its mating tooth (iii) is at the pitch point.
Using this efficiency map, select a 6th gear ratio such that the engine will operate with high efficiency when travelling at 120km/h on a flat road. Give the total gear ratio and the ratio required in the gear box. State any assumptions and give engine speed and torque and approximate efficiency for your chosen gear ratio.

SEE MORE QUESTIONS

Recommended textbooks for you

Automotive Technology: A Systems Approach (MindTa…

Mechanical Engineering

ISBN:

9781133612315

Author:

Jack Erjavec, Rob Thompson

Publisher:

Cengage Learning

Automotive Technology: A Systems Approach (MindTa…

Mechanical Engineering

ISBN:

9781133612315

Author:

Jack Erjavec, Rob Thompson

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

GET THE APP

About FAQ Academic Integrity Sitemap Document Sitemap

Contact Bartleby Contact Research (Essays)High School Textbooks Literature Guides Concept Explainers by Subject Essay Help Mobile App

GET THE APP

Privacy

Your CA Privacy Rights

Your NV Privacy Rights

About Ads

Manage My Data

bartleby, a Learneo, Inc. business

Gears	Input Speed (rpm)	Output Speed (rpm)	Input Torque (N.m)	Output Torque (N.m)
1	322	97	2,67	0,72
2	320	168	3.05	1,23
3	311	238	4,24	1,83
4	297	297	5,95	2,36
5	280	334	7,36	2,80