A PN-junction diode has a reverse saturation current rating of 20nA at 32C, if the forward voltage drop is 0.5V with a unity emission coefficient (n=1) [Note: the dynamic resistance is Vo/lol, find: a) The forward current of the diode? b) The dynamic resistance at the given conditions?

A PN-junction diode has a reverse saturation current rating of 20nA at 32C, if the forward voltage drop is 0.5V with a unity emission coefficient (n=1) [Note: the dynamic resistance is Vo/lol, find: a) The forward current of the diode? b) The dynamic resistance at the given conditions?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Solve the voltage across silicon diode of the given circuit below. ID1 0.3 V 32 V 28 V 0.7 V 32 V Ge…

A: if two diodes of different cut in voltage , then diode with lower cut in voltage will turn on . cut…

Q: Calculate the theoretical barrier height, built-in potential barrier and Schottky barrier width in a…

A: SOLUTION Given--> Si/Cr Junction Diode…

Q: 3) For a two pole, 50 Hz, 3 phase synchronous motor, the speed of rotating magnetic field is o 1000…

A: Given: A three phase synchronous motor has, Number of poles, P=2. Supply frequency, f=50 Hz.

Q: 2. The short-circuit secondary current in a transformer is 2 A. What is the primary current if the…

A: Given, A transformer has, Short circuit secondary current I2=2 A. Transformer turns ratio a=25.

Q: A fiber optic cable with a core diameter of 100 µm is to be spliced to a cable with a core diameter…

A: SOLUTION GIVEN--> CORE DIAMETER =100×10-6m…

Q: Find the equivalent inductance of the circuit shown in Fig. 6.31. Leg 4 H m m 8 H 7 H 20 H m m 10 H…

A: Given circuit,

Q: A transformer primary has 320 turns of wire and the secondary voltage measures 160 V when 40 V is…

A: Given: A transformer has, Primary turns N1=320. Secondary voltage V2=160 V. Primary voltage V1=40 V.…

Q: Design a 18 person voter system using 4 bit parallel adder(s) only. Use a minimum number of…

A: Given components: 4-bit parallel adders To design: An 18-person voter system using a minimum…

Q: In BJT transistor V₁ = 0.7 V and V₁ = 25 mV and reverse saturation current is BE 10-13 A. Find the…

A: Given- BJT transistor-VBE=0.7 VVT=25 mVReverse saturation current Is=10-13 ATo Find-The…

Q: 1) Calculate Vo1, & Vo2 for the circuit in Figure 1. Si Vo1 47k02 M +12 vo Figure 1 3.3 M Voz

A: Since you have posted the multiple questions so we are supposed to answer the 1st one

Q: An electric current is flowing through a long cylindrical conductor with radius a = 0.35 m. The…

A: Given data: The radius a=0.35 m The current density J=9.5 A/m2

Q: Draw a gate-level diagram of a comparator for checking if three 2-bit numbers (A, B, C) are…

A: given Three 2 bit numbers A,B,C

Q: 1₁-1₂ 1₁ + 1₂ Adding eqs. (i) and (ii), we have, 1₁ + 1₂ On solving eqs. (iii) and (in = j5 1₁-1₂ =…

A: The required current can be calculated by solving the given two equations and then convert the…

Q: 4. Draw the circuit structure of a TCR. By changing the firing angle of thyristors, how can we…

A: ANSWER CIRCUIT DIAGRAM OF THYRISTOR

Q: A 33 kV, 50 Hz. 3-phase underground cable, 6 km long uses three single core cables. Each of the…

A: We have been given an 33 KV 50 Hz 3-phase underground cable as, Length (l) = 6 Km = 6000 m Line…

Q: 138 Techniques of Circuit Analysis 4.18 a) Use the node voltage method to find vo for the circuit in…

A: Given:Circuit diagram

Q: Find the equivalent Inductance for the following circuit shown below. L oooo 0.5 H elle 2 H oooo…

A: Given circuit:

Q: A three phase line 30 km long delivers 2000 KVA at 33 kV voltage, 0.707 lagging power factor. If…

Q: Find the upper and lower limits for the system shown below. (Show me your work in details)

A: The heater input voltage and the corresponding temperature waveforms of the system are shown below,

Q: In the circuit shown, Find the value of the resistor R, for I = 40 mA. 5102 wwww Select one: O a 765…

A: Given data, I=40 mA Circuit diagram is given as,

Q: An alternating voltage is represented by V = 100 sin (2nt/0.01667). (1) Maximum value of voltage (2)…

Q: 4.81 Find the Norton equivalent with respect to the ter- minals a, b for the circuit seen in Fig.…

A: Given data: The given circuit in shown below,

Q: Design a circuit using two op-amps to implement: Vo = 3.5v1 + 4.2v2 - 5.5v3. Show all the…

A: Given: Voltage equation V0=3.5V1+4.2V2-5.5V3 Find: Circuit Calculation Assumptions Markings

Q: A 25 KVA single phase transformer has turns ratio of 100/29. If low voltage side is connected to 250…

A: Solution: Given data; KVA =25 KVA, single phase transformer ; turns ratio=N1N2…

Q: Two wire distributors ABC A is feeding on 240 v. AB Loop Impedance is 0.05 + J 0.150 and section…

Q: 3. The total capacitance for this circuit is SF t 10 F 10 F C₂ C₁

Q: 2.a. Find the total resistance between 'a' and 'b' for the circuit given below. 20 Ω www 162 a Rab…

A: Given:

Q: Determine the current I (with direction) for the networks shown. 1 6Ω 80 V 3Ω 26 V

A: Given circuit:

Q: What is a spike in noise term

A: ANSWER NOISE---> Noise is a…

Q: d Construct the truth table for the following circuit: D D -

Q: system. Check if the system y(n) = x(-n) is time variant or time invariant

Q: This configuration can overcome the disturbances. Close-loop System Open-loop System Closed-loop…

A: Definition: The expression control system is a set of mechanical or electronic devices that…

Q: Q3. Evaluate the circulation around the closed path shown in the Figure for, which represents a…

A: A vector is a single vector, but a vector field is a distribution of vectors over space and time.…

Q: Compensator function as

A: Compensator function as specialized filters.

Q: No start-up costs; no minimum up- or downtime constraints. a. Solve for the unit commitment by…

A: In unit commitment and economic dispatch, those units will be operated first which are economical…

Q: Consider a pn junction with the p region doped 1023 atoms m³ and the n region doped 10¹9 m³ at 300…

Q: Q27. A 15 V source is connected across a 120 resistor. How much energy is used in three minutes? 938…

A: Given - Power = P = 15 V Resistance = 12 Ω Time = t= 3 mins To find- Energy Used (E)

Q: 7. What is the no-load voltage when the full-load secondary voltage is 108 V and transformer…

A: Given: In a transformer, Full load secondary voltage V2fl=108 V. Transformer regulation VR=10%.

Q: QUESTION 1 Identify four tasks in addition to relay switching operations that PLCs are capable of…

A: Since you have asked multiple questions, we will solve the first question for you If you want any…

Q: 1. A lighting load of 600 kW and a motor load of 707 kW at 0-707 lag are supplied by two alternators…

A: Given L1 = 600kW L2 = 707kW @ 0.707pf lagging G1 = 900kW @0.9pf lagging G2 = ?

Q: What is 5ED4 07A4 when these values represent signed 16- bit hexadecimal numbers stored in…

A: Given data, The base-16 numeral system used in hexadecimal is. With fewer digits, it can be used…

Q: A fiber optic cable with a numerical aperture of 0.65 is to be spliced to a second fiber optic cable…

A: Given Numerical aperture of first fiber optic cable (NA1) = 0.65 Numerical aperture of second fiber…

Q: Find the average value of the voltage in the figure m 5V ov+ O 1.59 V O 63.7 V O 6.37 V O 10.5 V

A: Given a waveform Asked to find average value of the voltage Maximum value(Vm) = 5V

Q: Find the Thévenin's equivalent for the network in

A: For finding the thevinins we find the Zth and Vth across the terminals consider the loop currents I1…

Q: Two 3300 V star-connected alternators running in parallel supply the following loads : 800 kW at…

A: Given, (i) The active power, P1=800 kW The power factor, cosφ1=1 (ii) The active power, P2=600 kW…

Q: 3. According to Equal Area Criterion method, please explain how series capacitive compensation…

Q: 750kW alternators are operated in parallel. P₁ = 750kW, P₂ = 750kW Speed regulation of one machine…

Q: A 440/110 V single phase transformer when operated at no load has 6 A No current takes at 0.25…

A: solution: Given data; single phase transformer: 440/110 V, no load current Io=6 A, cosϕo=0.25,…

Q: (e mra Given an amplifier with an effective noise temperature of 15,000 K and an 8MHZ bandwidth,…

A: Given- Temperature = 15000 K Bandwidth = 8 MHz To find- Thermal noise level =?

Q: A 250 V d.c. shunt generator has 1250 watts constant loss. Find out load current at maximum…

Question

100%

A PN-junction diode has a reverse saturation current rating of 20nA at 32C,
if the forward voltage drop is 0.5V with a unity emission coefficient (n=1) [Note:
the dynamic resistance is Vo/lol, find:
a) The forward current of the diode?
b) The dynamic resistance at the given conditions?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A diode is doped with NA=1018/cm3 on the p-type side and ND=1018/cm3 on the n-type side. (a) What are the values of pp, pn, np, and nn? (b) What are the depletion-region width wdo and built-in voltage?
In PN junction in series with a 100 ohms resistor, is forwarded biased. So that a current of 100 mA flows. If the voltage across this combination is instantaneously reversed at t = 0 current through diode is approximately given by:
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Forward bias current equation given i If the =1 and Is= 10pA. Plot the I vs VD Forward bias characteristics of a PN Diode at room temperature by draw a graph and table of the graph. (b)Calculate and find Rd (details calculation)
Suppose a Schottky barrier diode can be modeled by the diode equation in Eq. as shown with IS =10−7 A. (a) What is the diode voltage at a current of 50 A? (b) What would be the voltage of a pn junction diode with IS =10−15 A and n =2?
The npn transistor is connected in an alternate“diode” configuration. Use the transport model equations to show that the i-v characteristics of this connection are similar to thoseof a diode as defined. What is thereverse saturation current of this “diode” if IS =5 × 10−16 μA, βF = 60, and βR = 3?
Consider the diode circuit shown below. If in the given circuit, Vs is replaced by a 12V battery and diodes D1 & D2 are considered ideal, what is the potential Vout equal to?
Consider the diode circuit shown and by assuming Vγ = 0.6 V and rf = 20 Ω; i. determine the diode voltage VD and output voltage Vo. ii. If the diode connection is reversed (i.e., the diode is in up-side down direction), compute the new diode voltage VD and output voltage Vo.
Draw the cross section for a pn diode similar to that as shown if the fabrication process utilizes a p-type substrate in place of the n-type substrate depicted as shown.
Sketch the energy band diagram for an ideal p+-n step junction diode showing the carrier activity in and near the depletion region when (a) VA = 0. (b) VA > 0. (c) VA < 0
A diode has a doping of ND = 1015/cm3 on the n-type side and NA = 1017/cm3 on the p-type side. What are the values of wdo and φj? What is the value of wd at a reverse bias of 10 V? At 100 V?
ELECTRONİC1 Provide two designs of shunt regulators utilizing the 1N5235 zener diode, which is specified as follows:VZ = 6.8V and rz = 5ohm for IZ = 20mA; at IZ = 0.25mA (nearer the knee), rz = 750ohm. For bothdesigns, the supply voltage is nominally 9V and varies by1V . For the first design, assume that theavailability of supply current is not a problem, and thus operate the diode at 20mA. For the seconddesign, assume that the current from the raw supply is limited, and therefore you are forced to operatethe diode at 0.25mA. For the purpose of these initial designs, assume no load. For each design findthe value of R and the line regulation.