A pot of water is boiling under one atmosphere of pressure. Assume that heat enters the pot only through its bottom, which is copper and rests on a heating element. In two minutes, the mass of water boiled away is m = 2.5 kg. The radius of the pot bottom is R = 8.0 cm and the thickness is L = 1.0 mm. What is the temperature of the heating element in contact with the pot?

A pot of water is boiling under one atmosphere of pressure. Assume that heat enters the pot only through its bottom, which is copper and rests on a heating element. In two minutes, the mass of water boiled away is m = 2.5 kg. The radius of the pot bottom is R = 8.0 cm and the thickness is L = 1.0 mm. What is the temperature of the heating element in contact with the pot?

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter1: Temperature And Heat

Section: Chapter Questions

Problem 49P: The height of the Washington Monument is measured to be 170.00 m on a day when the temperature is...

See similar textbooks

Similar questions

The height of the Washington Monument is measured to be 170.00 m on a day when the temperature is 35.0 . What will its height be on a day when the temperature falls to -10.0 ? Although the monument is made of limestone, assume that its coefficient of thermal expansion is the same as that of marble. Give your answer to five significant figures.
Two cylindrical metal rods—one copper, the other lead—areconnected in parallel with a temperature of 21.0 °C at one end and112 °C at the other end. Both rods are 0.650 m in length, and the leadrod is 2.76 cm in diameter. If the combined rate of heat flow throughthe two rods is 33.2 J>s, what is the diameter of the copper rod?
The heat required to melt a block of ice is 1165500 J. Estimate the total heat required to vaporize the same mass of water that is at 50 °C. ( Cwater = 4186 J/kg.°C, Lf = 3.33 × 105 J/kg, and Lv = 2.26 × 106 J/kg.)
A heavily insulated copper rod or diameter 2 cm and length 25 cm is used to pipe heat between two objects. If the rate of heat transfer is 100 W and the hot object has a temperature of 50oC, what is the temperature of the cold object in oC?
The radius and the length of a cylindrical metal are 5.00 cm and 20.00 cm at 25 C, respectively. After it absorbed 9000 J of heat, the temperature raises from 25 C to 85 C and its length expands to 20.02 cm. Then, the cylinder was immersed to the water covered with insulator. The water initial temperature was 25 C and with mass 500 g. (Specific heat capacity of water is 4200 Jkg-1c-1 )(Heat loss through the container and cover is negligible.) Determine the volume of the cylinder at 85 C.
A Styrofoam cooler has total wall area (including the lid) of 0.80m2 and wall thickness 2.0 cm. It is filled with ice, water, and cans of Omni-Cola, all at 0°C. What is the rate of heat flow into the cooler if the temperature of the outside wall is 30°C.? How much ice melts in 3 hours? Ksytrofoam=0.027 W/m-K A. 34.2 W , 1.04 kg B. 32.4 W , 1.04 kg C. 32.4 W , 1.40 kg D. 34.2 W , 1.40 kg
The bottom of a copper kettle hasa 9.0-cm radius and is 1.8 mm thick. The temperature of the outside surface is 102C and the water inside the kettle is boiling at 1 atm of pressure. Find the rate at which energy is being transferred through the bottom of the kettle (J/s)
The outer diameter of a glass jar and the inner diameter of its iron lid are both 760 mmmm at room temperature (20.0 ∘C). What will be the size of the mismatch between the lid and the jar if the lid is briefly held under hot water until its temperature rises to 62.5 ∘C, without changing the temperature of the glass? Use the coefficient of linear expansion for iron α= 1.2×10^−5 K^−1. Express answer in millimeters.
On a hot day, the temperature of an 82000-L swimming pool increases by 1.45°C. What is the net neat transfer, in joules, into the pool during this heating? Ignore any complications, such as loss of water by evaporation.
A copper bar of thermal conductivity 401 W/(m·K) has one end at 114°C and the other end at 24.0°C. The length of the bar is 0.180 m, and the cross-sectional area is 1.00 × 10−6 m2. What is the rate of heat conduction P along the bar?
and the length of the copper section is 0.800 mm. Each segment has cross-sectional area 0.00700 m2m2. The free end of the brass segment is in boiling water and the free end of the copper segment is in an ice-water mixture, in both cases under normal atmospheric pressure. The sides of the rods are insulated so there is no heat loss to the surroundings. What mass of ice is melted in 6.00 min by the heat conducted by the composite rod?
A spherical brass shell has an interior volume of 1.55 x10-3 m3. Within this interior volume is a solid steel ball thathas a volume of 5.00 x 10-4 m3. The space between the steel ball and the inner surface of the brass shell is filledcompletely with mercury. A small hole is drilled through the brass, and the temperature of the arrangement is increasedby 10 °C. What is the volume of the mercury that spills out of the hole?